Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
INSTALLATION 1 Before servicing ask the customer what the trouble is. 2 Check the adjustments. (Power supply :220-240V~, Removal of transit bolts etc..) 3 Check the troubles referring to the troubleshooting. 4 Decide service steps referring to disassembly instructions. 5 Then, service and repair. 6 After servicing, operate the appliance to see whether it works O·Kor NOT. STANDARD INSTALLATION The appliance should be installed as follows. REMOVE THE TRANSIT BOLTS INSTALL THE APPLIANCE ON FLAT AND FIRM SURFACE ADJUST THE HORIZONTAL Remove the transit bolts (4EA: ) with supplied wrench. Keep the transit bolts and wrench for future use. Insert the 4 caps provided into the hole. 1 Turn the adjustable feet to set the appliance horizontally. Low High The appliance goes up by rotating the feet clockwise. The appliance comes down by rotating the feet counter-clockwise. 7 HOW TO CONNECT INLET HOSE Check that the rubber is the inside of valve connector. Connect inlet hoses firmly to prevent leak. CONNECT DRAIN HOSE · Make sure that the hose is not twisted. · Avoid submerging the end of the hose. . The drain hose should be placed under 100cm from the floor. CONNECT POWER PLUG · Connect the power plug to the wall outlet. · Avoid connecting several electric devices, It may be the cause of a fire. 8 7 TEST OPERATION 1 Preparation for washing. · Connect the power plug to the outlet. · Connect the inlet hose. 2 Press the power button. 3 Press the START/PAUSE button. 6 Check the water heating. · Press both Time Delay and Pre Wash buttons simultaneously the present temperature will be displayed. · Check if the drum rotates clockwise and counterclockwise. 5 Check automatic reverse turn. 4 Check the water supply. · Check if water is supplied through the detergent dispenser. · In case of cotton program. 7 Check drain and spin. · Power off and then power on. Turn on Spin lamps after pressing the Start/Pause button and Start the machine again. · Check drain and spin. · Power off and then power on. · Check if the door can be opened after Door Lock lamp turns off. 8 Power off and open the door. 9 Water removal. · If SVC is needed during check, remove the remaining water by pulling out the hose cap. 9 5. OPERATION Wash program selector • 13 programs can be set depending on the type of the laundry. • If the power button is pressed, all lamps are on • By turning the dial, [Cotton - Cotton Quick - Synthetic - Duvet - Bulky - Quick 30 - Rinse+Spin - Spin - Delicate - Hand Wash/Wool - Bio Care - Boiling Care - Baby Care] can be selected. (The opposite is possible) LED display •Display the estimated remaining time (Hour : Minute) to finish. • In case of abnormal operation, error indications are displayed. ( ) • See troubleshooting guide. Start/Pause button • Use the button to start or pause wash cycle. • The power turns off automatically 4 minutes after the pause button is pressed. Spin Button • By pressing the Spin Button the spin speed can be chosen • F10**ND(1~9) Rinse Hold/No spin/400/800/1000 • F12**ND(1~9) Rinse Hold/No spin/400/800/1200 10 QC Test Mode -Press Temp. and Spin and Power buttons simultaneously Water level frequency buttons -Press Intensive and Crease Care simultaneously Time Delay & Beep ON/OFF • Press the button when reservation washing is needed. • When the button is pressed, [ ] is displayed, maximum delay of [ ] hours can be set. • Each press advances time delay by the hour. • Use [Power] button to cancel [Time Delay] • [Time Delay] means the time required from the present to the completion of washing. • The Beep on/off function can be set by pressing and holding the Time Delay button (About 3 seconds). The Beep on/off function can be set at any time and it is automatically cancelled in the event of a power cut. The Beep on/off function also works when power is off. Child -Lock • Child Lock system can be set and canceled by pressing and holding both Medic Rinse button and Pre Wash button simultaneously more than 3 seconds. Tub Clean • Tub Clean course can be set by pressing and holding Intensive and Crease Care button simultaneously. • Tub Clean is special cycle to clean the inside of the washer. Option • Medic Rinse : Function that offers more purity in rinse operation by maintaining the optimum temperature for elimination of remnant detergent. It can be selected in all courses with the exception of Quick 30. Hand Wash/Wool, Delicate course. • Intensive : • If the laundry is heavily soiled “Intensive” option is effective. • By selecting the Intensive option, the wash time may be extended, depending on the program selected. • Pre Wash : If the laundry is heavily soiled, “Pre Wash” course is effective. Pre Wash is available in Cotton and Synthetic Program. • Crease Care : If you want to prevent crease, select this button with spin Power button • Press the button to turn power on and off. • Press the button to cancel th...
Dieses Handbuch ist für folgende Modelle:Waschmaschinen - F1020NDR (2.12 mb)
Waschmaschinen - F1020TDR (2.12 mb)
Waschmaschinen - F1220NDR (2.12 mb)
Waschmaschinen - F1220NDR5 (2.12 mb)