Stimmen - 5, Durchschnittliche Bewertung: 4.6 ( )

Hersteller: Beko Dateigröße: 657.41 kb Dateiname: Unterrichtssprache:

Ending the program through canceling The program which is selected first will keep on going even if the position of the program selection button is changed. A new program can be selected or started after “Program is cancelled” in order to change the washing program. To cancel any selected program; • Press “Start/Pause/Cancel” button for 3 seconds. At the end of this time, “Start/Pause/Cancel” light and all lights go off and “Spin” lamp illuminates. If the door is unlocked, all lights on the indicator will go off and the “Ready” lamp will illuminate. You can select and start a new program when the “Ready” light is lit. • The machine can drain all the water or can take in water for 3 times at most to cool down the clothes and complete the draining process. Also the “Spin” light illuminates if the cancellation process is activated in the middle of the program. The “Spin” light goes off when discharging process is completed. The door can be opened and a new program can be selected when the “Lid” lamp illuminates. End of program The “Ready” lamp on the program follow-up indicator will light up when the program comes to an end. The door can be opened and the machine becomes ready for a second cycle. Press the “On/Off” button to shut down the machine. 6 Quick instructions for daily use Preparation 1. Turn the tap on completely. Check if the hoses are connected tightly. 2. Place the laundry in the machine. 3. Add detergent and softener. Starting 1. Press the “On/Off” button. 2. Select the programme and the temperature. 3. If required (according to your machine’s model): – select any auxiliary function, – adjust the spin speed, – set the time delay, 4. Close the loading door. 5. Press “Start/Pause/Cancel” button. Canceling a program • Press “Start/Pause/Cancel” button for 3 seconds. At the end of this time, “Start/Pause/Cancel” light and all lights go off and “Spin” lamp illuminates. If the door is unlocked, all lights on the indicator will go off and the “Ready” lamp will light. You can select and start a new program when “Ready” light illuminates. • The machine can drain all the water or can take in water for 3 times at most to cool down the clothes and complete the draining process. Also the “Spin” light illuminates if the cancellation process is activated in the middle of the program. The “Spin” light goes off when discharging process is completed. The door can be opened and a new program can be selected when the “Ready” lamp illuminates. Adding more laundry • This is only possible under the following conditions: – during time delay, C You may add or remove laundry during the time delay (until the program starts). – At the beginning of a washing cycle, C Machine allows adding more laundry during a later step only if the water level is low enough to open the loading door or if the temperature in the machine is low enough. In order to add laundry after the start-up of the program: 1. Press “Start/Pause/Cancel” button. Wait until the door is allowed to open. When the “Ready” lamp is on continuously, continue to the next step. 2. Open the loading door and put in more laundry. 3. Close the loading door. 4. Press “Start/Pause/Cancel” button. Program is in rinse hold mode C Clothes may be left to soak in the machine as long as desired after filling during the last rinse step. When it reaches this position while the machine is running, the “Start/Pause/ Cancel” light will flash. If you wish to spin when the machine is in this mode: Adjust the spin speed. Press “Start/ Pause/Cancel” button. Program resumes. Your machine drains the water and spins your laundry. If you want to discharge the water without spinning: Press “Start/Pause/Cancel” button. The program continues and only drains the water. Re-spinning the laundry The control system for an unbalanced load can pause the spinning in cases when the distribution of the laundry in the drum is not balanced. If you want to re-spin the clothes: 1. Rearrange the previously placed clothes in machine. 2. Select the spin program. 3. Set the spin speed if spin speed adjustment is available on your machine. 4. Press “Start/Pause/Cancel” button. After the program is finished 1. “Ready” lamp will light up on the program follow-up indicator. Open the loading door and take out the clothes. 2. Press the “On/Off” button. 3. Turn the water tap off. 4. Eliminate any folding of the rubber seal on the loading door and check for impurities. 5. Leave the loading door and detergent drawer open to dry. 7 Cleaning and care Detergent drawer Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. 2. Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appro...

Herunterladen

Geben Sie zwei Ziffern: