Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Beko Dateigröße: 1.14 mb Dateiname: Unterrichtssprache:

Additional Laundry Press the Start/Pause button. If the water level does not exceed the limitations, in 1 to 2 minutes door open led will come on. It means the washing machine is ready to add laundry. If door open led is not lit up after 1-2 minutes, it means the water level inside the machine is too high and it is not allowed to open the door and add laundry. (Look at Program Cancelling). If you change your mind as not adding laundry, press Start/Pause button again to let the program continue. 12 End of the Program If all the wash programs are finished, all the leds on the program follower will be on . “1-2 minutes” for door open is displayed on remain time display. After1-2 min door open led will light up. At the end of the washing, all related leds on the control panel will be on. Related duration time of the selected program is displayed and the machine is ready to start again. To switch off the machine, press the On/Off button. Unloading the machine Machine stops automatically after all the programs are finished. Turn off the tap. In 1-2 min, after the door open led lights up, press the door open button and open the door. Press the On/Off button to switch off the machine. Unload the machine and leave the front door open. Check to see if there is any water left in the door hood. If so, remove with a soft cloth. 13 Time Delay By using the time delay buttons, starting time of any program can be delayed. Time delay can be set at intervals of 30 min. On the display, the delayed starting time is added to the duration of the program. For example, if the program duration is 2 hours and 16 min and you delayed the program for 2 hours, the display will show “4:16”. After the time delay is set, press Start/Pause button. The washing period will be started after 2 hours Program Cancelling If the program has not started yet, you can cancel the selected program by pressing Start/Pause button for 3 seconds. After 3 seconds the led of the Start/Pause button will be off and the led of the selected program will be on, where it is possible to set a new program If the program has started and you want to cancel it, press Start/Pause button for 3 seconds. The program will moveto the “spin” step and related led on the program follower will be on. Machine will start to pump for draining and the door can be opened after the door open led is on. 14 5 Care and maintanence 5 Care and maintanence Detergent dispensing drawer Clean when necessary: 1. Open the drawer as far as possible. 2. Push down the depression on the suction cup and pull the drawer out completely. 3. Clean the drawer under warm running water. Pull off the suction cup; Clean suction cup and opening in the drawer with warm running water, pierce the opening with a needle if necessary. Replace the suction cap. 4. Wipe off detergent residue from the drawer guides. If present, remove calc deposits from the water-jet nozzles (inside the drawer). Foreign matter trap • Clean the foreign matter trap at least once after every 30 wash cycles! • Clean foreign object trap, if foreign objects (coins, buttons, baby socks, etc.) are blocking the suds pump. • Drain left-over water before cleaning (see below). Water intake filter At the end of the water intake connection module and water inlet hose-tap side, there exists filters. These filters prevent any dirt and objects passing into the machine. It is advisable that these filters should be cleaned every 30-40 washes. To clean the filter, first turn the tap off. Then, disconnect the hose and clean the filter with a thin brush. If the filter is very dirty, you may clean it by pulling out with pliers. To clean the filter at the tap side of the hose, pull it out by hand and clean the filter under the tap water. Hose To prevent any leakage, have a technician to control the hoses every two years. If the machine is placed at cold ambient temperatures, the water remining inside the pump and hoses should be removed from the filters. Also to prevent freezing, empty the water intake hoses by disconnecting from taps. Drum Do not leave any metal objects (pins, needles, etc.) inside the drum. These objects may cause rust on the drum surface. Do not clean the drum with scratching elements. Cleaning the pump filter Drain off the water completely… • before cleaning the foreign matter trap; • before transporting the machine (e.g. when shifting house); • when there is a power failure ("emergency draining"); • when there is a danger of frost. At room temperatures below 0 °C the remaining water in the appliance could freeze, damaging it. 1. Switch appliance off, unplug the power cable, close the water tap. Allow hot suds to cool off sufficiently. This poses a risk of scalding. 2. Open the service door by pushing on the button. Take out the drain pipe and hold it over a bowl. Pull the seal off the drain hose and allow the water to drain out one bowl at a time. There may be more than 20 litres of water left in the machine when the drum is bull (e.g. afte...

Herunterladen

Geben Sie zwei Ziffern: