Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Alliance Laundry Systems Dateigröße: 1.1 mb Dateiname: Unterrichtssprache:

Using a spanner, unscrew and remove the rear right-hand bolt and lay the machine on its back, taking care not to squash the hoses. This can be avoided by placing one of the corner packing pieces between the machine and the floor. Remove the polystyrene block from the bottom of the machine and release the two plastic bags which are fixed under the filter door. Carefully remove the right-hand bag (1) then the left-hand bag (2) by pulling them towards the centre of the machine. Set the machine upright and remove the two remaining bolts from the back. Pull out the three plastic spacers from the holes into which the bolts were fitted. Plug the open holes with the plugs which you will find in the plastic bag containing the instruction booklet. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. • Before placing it on small tiles, apply a rubber coating. • Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine. • If it is impossible to avoid positioning the machine next to a gas cooker or coal-burning stove, an insulating panel (85x57 cm) covered with aluminium foil on the side facing the cooker or stove, must be inserted between the two appliances; • The machine must not be installed in rooms where the temperature can drop below 0°C. • The water inlet hose and the drain hose must not be kinked. • Please ensure that when the appliance is installed, it is easily accessible for the engineer in the event of a breakdown. Levelling Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Installation on a suspended floor Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor beams with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable. Water inlet (cold water connection only) Connect the hose Model 16800 Model 14800 to a tap with a 3/4” thread. Installation should comply with local water authority and building regulations’ requirements. Installation Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. Do not connect to a hot water supply. Model 16800 The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window “A”. Should this occur, turn the water tap off and refer to your Service Force Centre to replace the hose. Water drainage The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece” supplied. The standpipe should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. When discharging into a stand pipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4”) and no less than 60 cm (23.6”) above floor level. The upright standpipe should have a minimum length of 30 cm (12”) from the bottom "( )*&+*,"#*-./(* &+*,'"* ./ of the elbow to the top of the pipe (see dia gram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. (*"&+*,$'./"!++*,$0./ + $' Installation If you intend the drain hose from the machine to empty into a sink, make sure that the sink is empty and the plug hole is not blocked. Use the plastic “U -Piece” supplied. Important Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. In the interest of the environment Washing machines and dishwashers should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local water authority. <. <. 1231453216(1121816:85:85226(24162789::78:22 Installation 5(%358$"(%32 Electrical connections WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. 655. $"(. :8. If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appro...

Herunterladen

Geben Sie zwei Ziffern: