Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Alliance Laundry Systems Dateigröße: 828.96 kb Dateiname: Unterrichtssprache:

Note: Never turn the power off while the computer mode switch is in the PROGRAM position. Such action will disorder portions of the programmed data, necessitating reprogramming of some or all of the existing cycles. Always return the mode switch to RUN position before turning the power off. Keypad Operation of the S-computer control is performed with a 4-key touch keypad and LED display located on the front of the machine. See Figure 3. The following table describes the function of the individual keys when the machine is in RUN mode. Keypad Key Description Up Used in cycle selection; pressing this key moves among cycles from smaller to greater. Down Used in cycle selection; pressing this key moves among cycles from greater to smaller. Start Used to start a cycle. Stop Used to stop a cycle. Up Down Start Stop B008RE3A LED Display Figure 3 14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073 Safety The following table lists the various displays and what they mean. The operator should become familiar with these computer displays. Display Indications Display Meaning Display Meaning S-05 Program identification code (ROM) This is an example only. bFIL Warm fill (both hot and cold) Hold Wait...power has just been turned on. HFIL Hot fill CY Cycle (followed by two-digit number) LOLE Low water level CHEC/CYC* Test cycle selected. HILE High water level FAr Degrees Fahrenheit SUP1 Supply 1 CEL Degrees Celsius SUP2 Supply 2 PrE Prewash segment (1st of 8 segments) SUP3 Supply 3 UASH Wash segment (2nd of 8 segments) SUP4 Supply 4 FIL1 First rinse (3rd of 8 segments) SUP5 Supply 5 (supply 1 and 2) FIL2 Second rinse (4th of 8 segments) SUP6 Supply 6 (supply 2 and 3) FIL3 Third rinse (5th of 8 segments) SUP7 Supply 7 (supply 3 and 4) FIL4 Fourth rinse (6th of 8 segments) STOP Stop routine FIL5 Fifth rinse (7th of 8 segments) SdLY Spin coast delay FIL6 Sixth rinse (8th of 8 segments) donE Cycle and stop routine have ended. CFIL Cold fill door Door not properly closed. SPIn/tIME* Reads “SPIn” for one second, then “tIME” followed by time for spin. FILL/STOP* Programmed water level not reached after 30 minutes. tSFL Temperature sensor failure or temperature out of range. FULL The computer detects low water level or higher when none should be present. *Display indications separated by a slash represent an alternating display. F232073 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 15 Safety Start-Up Turn on the main power source (circuit breaker or cut-off switch on the wall). An identification code will appear for approximately five seconds. Then the display will flash “hold” for thirty seconds. The display will then read “CY” followed by a two- digit cycle number (01 – 30) to indicate that a cycle can be selected. This display will be shown at all times that power is on between cycles, indicating that the door-unlock solenoid will function if the door-unlock button is pressed. The machine is then ready for loading and unloading. Opening Door Press and hold the door-unlock button on the left side of the control panel. Press the round button on the door handle and turn the door handle downward. Loading . Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury. SW025 Load the machine to full capacity whenever possible, but do not exceed the rated dry-weight capacity of the machine if the fabric to be washed is quite dense, closely woven, and heavily soiled. Overloading can result in an inferior wash. The operator may need to experiment to determine load size based on fabric content, soil content, and level of cleanliness required. Partial loads are a waste of energy, water, and chemicals, and cause greater machine wear than full loads. Partial loads also increase the possibility of a severe out-of-balance condition. Never operate the machine with a bypassed or disconnected out-of-balance switch. Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage. SW010 When loading is complete, ensure that all fabric is inside the basket. Then close and lock the door by rotating the door handle counterclockwise until the door handle pushbutton pops out. The machine should not start or run unless the door is both closed and locked. . Check the door safety interlock daily before the machine is placed in operation. SW024 Note: When washing items which may disintegrate, such as mop heads or sponges, use laundry net bags to prevent drain blockage. 16 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073 Safety Supply Dispenser Both liquid and powder supplies may be added by raising the flexible cover of the dispenser. Liquid supplies may also be injected directly into the supply dispenser by an external chemical supply system. Note: When a liquid supply is manually added to the machine through supply compartments 1 or 2, that liquid is imm...

Herunterladen

Geben Sie zwei Ziffern: