Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: AEG Dateigröße: 1.51 mb Dateiname: 5ef2b34a-0da4-4c64-9bb8-7c3f6f09f2aa.pdf Unterrichtssprache:

For this reason, the cycle will always be completed. If heavier fabrics in such out-of-balance loads should ever contain excessive moisture at the completion of the cycle, redistribute the clothes in the washer and reset the control dial for the final spin period. Overload Protector A built-in protector automatically shuts off the washer motor in case of an overload. This can occur if: • The load being washed is too heavy. • Too many appliances are plugged into the line operating your washer. • A low voltage condition exists on the line. • Lid is opened and closed repeatedly. The overload protector permits the washer to start again when the motor has cooled to a safe operating temperature. If the motor stops repeatedly, call your service technician. Cycles, options, lightsWhat can & cannot be washedoperating FeaturesNotes Care & Cleaning 1. After washing, leave the lid open until the interior is dry. 2. Check hoses to be sure there are no kinks or knots. 3. Your washer should not be installed where temperatures will go below freezing, as damage to the washer could result. 4. To clean, occasionally wipe exterior with a clean damp sponge or cloth. Do not use polish on plastic parts. 5. Lifetime lubrication is done at the factory, so your washer never needs to be oiled or greased. 6. Do not lay heavy or sharp objects on top of your washer. 7. The top of the washer should not be used for removing stains from garments. Some stain removers, such as rust remover, will mar the finish. 8. Remove pins, buckles or other sharp objects from clothes to prevent scratching interior parts. 9. Clothes should not be stored in washer. 10. Bleach, detergent, solvents, etc. spilled on the top of your washer that are allowed to remain will remove the glossy finish. Remove all spills with a damp, soft cloth. 11. If you close your home for the winter, have a service technician drain the washer. Unplug cord from electrical outlet and disconnect hoses from faucets. Cleaning the Interior Clean the interior of the washer periodically to remove any dirt, soil, odor, mold, mildew or bacteria residue that may remain in the washer as a result of washing clothes. We recommend taking the following steps every 60 to 120 days to clean and freshen your washer interior. The frequency with which the washer should be cleaned and freshened depends on factors such as usage, the amount of dirt, soil or bacteria being run through your washer, or the use of cold water. Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor and/or permanent stains on the washer or wash load. To clean and freshen the washer interior: 1. Add a measured amount of chlorine bleach to the bleach dispenser, following package directions. 2. Add 1/4 cup of detergent to the tub. 3. Run the washer without a load through a complete cycle using hot water. 4. Repeat the process if necessary. Cycles, options, lightsWhat can & cannot be washedoperating tipsdishwasher useloadingControls FeaturesNotes Troubleshooting Won’t Fill • Plug cord into live electrical outlet. • Check fuse or reset circuit breaker. • Turn the control dial to proper cycle and restart the washer. • Turn both faucets on fully. • Straighten inlet hoses. • Disconnect hoses and clean screens. Hose filter screens may be plugged. Won’t Agitate • Check fuse or reset circuit breaker. • Make sure the lid is completely closed. • Turn the control dial to proper cycle and restart the washer. • Pauses are normal. Wait and see if the washer will start again. Won’t Spin • Check fuse or reset circuit breaker. or Drain • Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction, call for drain service. • Close lid and restart the washer. For your safety, washer will not spin unless the lid is closed. • Suds lock – caused by too much suds. Rewash without detergent. Use correct amount of a low-sudsing detergent. Load is Wet • Unevenly distributed load. Redistribute the load, close the lid and restart the washer. Check for leveling. Be sure water level is acceptable for load size. • A normal spin speed is recommended for heavy loads like jeans or towels. Stops • Plug cord into live electrical outlet. • Check fuse or reset circuit breaker. • Close lid and restart the washer. For your safety, washer will not agitate or spin unless lid is closed. • This may be a pause in the cycle. Wait briefly and it may start. Leaks Water • Make sure hose connections are tight. • Make sure end of drain hose is correctly inserted and secured to drain facility. • Avoid extended soaking – soak for 30 minutes or less. • Avoid overloading. Is Noisy • Be sure washer is leveled properly as outlined in installation manual. • Weak floors can cause vibration and walking. • Operating sounds will vary depending on agitation speed. Fills with • Turn both faucets on fully. the Wrong • If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and Temper...

Herunterladen

Geben Sie zwei Ziffern: