Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Indesit Dateigröße: 184.13 kb Dateiname: Unterrichtssprache:

- Use the correct quantities of detergent: do not use too much detergent; remember that not only will this make rinsing more difficult but also pollutes the enviroment. -Use the economy buttons: when washing small laundry loads use the Economy button if available on your washer and reduce the detergent quantity. -Your washer features automatic consumption control, this means that you can wash laundry loads from 1 - 5 kg with considerable savings. Your washer will use just the right amount of water and electricity. All you need to do is dose the detergent. -Fabric softeners: always use a softener; not only do these perfume and soften your laundry, they also make it easy to iron, saving you time. General maintenance After every wash Leave the door open and wipe the door gasket dry after each wash so that damp or odours do not form. Remove the plug Before cleaning or servicing always remove the plug from the socket. This is for safety reasons. No solvents or abrasive substance You do not need solvents or abrasive substances to clean the outside of the washing-machine and the rubber parts. Just use a cloth, warm water and soap. Detergent dispenser drawer This can be removed and cleaned. Just pull it towards you, as shown in the diagram, and leave it under running water for a few minutes. Unplug the machine when you go away It’s best to unplug the machine when you go away, turn off the water supply and leave the machine door open or ajar. The drum and rubber door lining will dry and no unpleasant odours will form inside. When moving house When you move, all you need to do is secure the inside of the machine with the transit screws (supplied with the packaging of the machine) so that it will not be damaged. Cleaning and special servicing Hose Check the hose once a year. It should be replaced if any signs of splitting or damage can be seen. The machine is under a lot of strain while operating and this may cause a cracked hose to split open suddenly. Inspecting the drain pump Your washer has a self-cleaning pump and therefore requires no cleaning or mainteannce. Removing limescale Water contains increasing amounts of limescale because of pollution. If you live in a hard water area in addition to using water-softener in each wash, it is a good idea to put the machine through a cycle without laundry or detergent, just using limescale remover. 7 GB Trouble shooting If the machine does not seem to be working properly before calling the service engineer there are a number of things you can check. Perhaps you have forgotten to push in a button or you are not using the machine properly. Machine won't start Make sure: the appliance is plugged to the mains socket; you have electricity in your home, the door is firmly shut, the ON/OFF button D is on I, the programming cycle knob, in washers which have one, is on O, the programme is properly set and the mains water tap is open. Machine won't fill Make sure: the water tap is open and connected correctly to the hose; the water mains has not been cut off and that water pressure is sufficient; also check the hose for kinks. Water is pumping in and out all the time Make sure: there are no kinks in the drain pipe and that it is at least at a height of 60-100 cm; the pipe mouth is not below water level and that the wall drain has no air outlet. If the problems continue even after you have checked these points, shut the water tap and turn off your washer. Problems with pumping out water or spinning Make sure: the programme selected has a draining cycle; the non creasing "hydropstop" button, on washers which have one, has not been pressed accidentally; the drainage pump is not jammed; the drain pipe is bent; the drainage piping is plugged; any drainage pipe extensions are properly connected and do not prevent water flow. Lots of vibration during the spin Make sure: the internal oscillating unit was released correctly at the time of installation (see installation instructions); the washer is levelled correctly or too tightly fitted between furniture units and the wall. Your washer is leaking. Make sure: the ring nut of the supply pipe is firmly tightened; the detergent dispenser is not plugged and the drainage pipe is firmly fixed. Excessive formation of suds. Make sure: the type of detergent you have used - is it suitable for an automati washer - have you used too much detergent? If despite all this your washer is still not running properly, call your local Authorized Service Centre providing the following information: -fault -model code (Mod. ....) and serial number (S/N ....) shown on the data plate at the back of your washer. Never use the services of an unauthorised servicing technician and insist on the use of original spare parts. GB 8 Installation Transit packing After removing the packing, check the appliance for damage. If you have any doubts do not use the washer and call a qualified technician. Keep the packaging components (plastic bags, polyester foam, nails etc.) out of ...

Herunterladen

Geben Sie zwei Ziffern: