Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Is the drain hose positioned too low? It must be installed at a height ranging from 60 to 100 cm. Is the end of the hose immersed in water? Does the wall drainage system have a breather pipe? If the problem persists even after these checks, turn the water supply off the machine and call for assistance. If you live on an upper floor of your building, there may be a problem with your drain trap. To solve this problem, a special valve must be installed. Instructions for installation and us. Is the drain hose kinked? Is there space between the The tract of the drain hose machine and adjacent must be as straight as units? If it is not a built-in possible. Make sure the drain model, the washing machine hose is not squashed or will oscillate a bit during the kinked. spin cycle. A few cm of space should therefore be left Is the washing machine’s around it. drain duct clogged? Is there an extension of the drain hose? If so, is it positioned The washing machine incorrectly, blocking the Too much foam. does not drain or spin. water flow? Is the detergent appropriate Does the selected for machine washing? programme incorporates Check whether the definition water draining? Some on its label reads “for machine programmes stop at the end wash” or “hand and machine of the wash cycles and wash”, or any other similar draining will have to be The washing machine wording. selected manually. leaks. Is the correct amount being Is the “Easy ironing" used? An excessive amount function -where provided Is the metal ring of the inlet of detergent, besides selected? Complete the hose properly attached? Excessive vibration producing too much foam, programme by pressing the Turn off the water supply, during the spin cycle. does not guarantee a more select button. unplug the appliance and try effective wash, and causes tightening its attachment Is the drain pump clogged? Have all transit screws been scaling in the internal parts of without forcing it. To check it, turn off the water removed durind instal-the appliance. supply, unplug the washing lation? See the following Is the detergent dispenser machine and follow the page on installation obstructed? Remove and If, despite all checks, the instructions on page 12, or procedures. wash it under tap water. washing machine fails to call for technical assistance. function and the problem Has the washing machine Is the drain hose well persists, call your nearest been levelled correctly?The attached? Turn off the water authorised Customer Service Always get levelling of the appliance supply, unplug the appliance Centre, providing the following assistance from should be checked and try tightening its information: authorised periodically. Adjust the feet attachment. -the nature of malfunction technicians and and check them with a level. -the model type no. (Mod. ....) always insist on -the serial number (S/N ....) original spare parts. This information can be found on the data plate situated at the back of the washing machine. Technical characteristics Model WE 16 Dimensions width 59,5 cm height 85 cm depth 53,5 cm Capacity from 1 to 5 kg Electrical connections voltage 230/240 Volt 50 Hz maximum absorbed power 1850 W Water connections maximum pressure 1 MPa (10 bar) minimum pressure 0,05 MPa (0,5 bar) drum capacity 46 litre Spinning speed up to 1600 rpm Control programs in compliance with IEC regulation 456 programme 3; temperature 60°C; rinsing level ; wash Intensity ; carried out with 5 kg load. This appliance conforms with the following E.E.C. directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications Instructions for installation and us. Installation and removal When the new washer arrives Whether new or just transported to a new house, installation is extremely important for the correct functioning of your washing machine. After removing the appliance from its packaging, check that it is intact. If in doubt, contact a qualified technician immediately. The inside of the machine is supported, for transportation, by four screws on the back panel. Before using the washing machine, remove the screws, remove the spacers together with the rubber tubes attached to them (keeping all the parts) and use the plastic plugs provided to fill in the holes. Important: Use the cap (provided) to close the 3 holes which housed the stop pin, situated in the right-hand part of the lower back of the washing machine. Levelling The washing machine must be levelled appropriatey in order to guarantee its correct functioning.To level the appliance, the front feet must be adjusted; the angle of inclination, measured according to the worktop, must not exceed 2°. When placed on carpet, make sure the ventilation is not reduced. The front feet are adjustable. Retain the transit screws, spacers and washers. Should you move house then these should be replaced to support the inside of the machine to prevent damage when tr...