Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Buhler Dateigröße: 4.45 mb Dateiname: Unterrichtssprache:

1. Raise loader to provide clearance to engage both parking stands. Shut off tractor. Standing along the outside of the loader arms remove parking stands from storage position and engage within the loader mainframe. buhler Allied Front-End Loader - 20 - P4094 2. Lower attachment level to the ground while engaging float position. Ensure attachment rests firmly on ground with minimal downward pressure. If required extend bucket cylinders to rotate upright rearward. At this stage the pin should have no pressure. Set tractor park brake and remove loader lock pins. Check hydraulic hoses such that they will not get pinched or stretched during removal. WARNING Operate hydraulic controls slowly. Loader will disengage from the mounting kit and may shift if not on firm level ground. 3. Retract bucket cylinders to raise upright and disengage from the loader mount cradle. If additional clearance is required, extend lift cylinders while slowly backing the tractor away from the loader. 4. After the tractor is clear of the loader, retract all cylinders to protect the shafting. Shut tractor off and set park brake and relieve oil pressure in hoses by moving valve control. Disconnect hydraulic loader hydraulic hoses at the quick couplers. IMPORTANT: Cap both male and female couplers. Wrap loader hoses over loader arm. buhler Allied Front-End Loader - 21 - P4094 INSTALLING / REMOVING LOADER ATTACHMENTS Installing: 1. Position tractor centrally within the bucket hooks. Dump Quick-tach slightly from vertical position. Slowly drive the tractor forward until the Quick-tach contacts the bucket. 2. Slowly raise the loader to engage the Quick-tach within both bucket hooks. When both hooks are resting on the Quick-tach rollback the bucket. Shut tractor off. Lock using both Quick-tach pins and secure with hairpin clips. CAUTION Verify attachment installation from tractor seat by lowering level attachment to ground and retracting the lift cylinders. Removing: 1. Rollback attachment and lower near ground position. Shut tractor off. 2. Remove both Quick-tach pins and place in storage position. Place level attachment on ground. Slowly dump attachment while backing tractor away. Pin in lock position. Pin in storage position buhler Allied Front-End Loader - 22 - P4094 LUBRICATION Lubricate loader bushings and pivots every eight hours of average operation with high-grade grease. For grease fitting locations see illustration below. Select grease based on the expected outside temperature range. Lithium, Molybdenum and synthetic greases are preferred. Use the tractor hour meter as a guide. Increase lubrication intervals for extreme use or adverse conditions. Each pivot should be lubricated until grease is visible at pin. TSL Loader Shown IMPORTANT: Ensure that grease fittings accept grease. Should any fitting become plugged, replace immediately. Pivots not greased as specified would cause premature wear of pins and bushings. Lubricate both right and left sides every 8 hours. buhler Allied Front-End Loader - 23 - P4094 MAINTENANCE General Inspection: CAUTION Lower attachment and loader to ground, place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing loader. WARNING Relieve hydraulic pressure before repairing, adjusting or disconnecting hydraulics components. Escaping hydraulic oil can penetrate skin causing serious personal injury. If injured consult a physician immediately. WARNING Never work beneath a raised loader unless it is securely supported. The control lever can be moved or a hydraulic leak could cause the loader to drop resulting in serious injury or death. Refer to the Lift Lock Instructions Decal for proper use of the lift locks. Lift Locks: The lift locks on your loader are to be used whenever someone is attempting to be under the loader or for tractor servicing. When using the locks ensure loader is free of any load in the loader attachment or no attachment. To engage, raise loader sufficient for lift lock clearance. Swing each lift lock forward resting on the cylinder rod below the head plate as shown. Turn off the tractor and slowly lower the loader until the cylinder head plate rests up against the lift lock. Then lock joystick in neutral position. Pins and Bushings: Every 6 months or 1000 hours check loader and cylinder pivots for movement that would be due to bushing or pin wear. Change bushings when excessive movement is noticed and replace any worn or rough surfaced pins. buhler Allied Front-End Loader - 24 - P4094 Mounting Kit: After the initial 2 weeks or 40 hours of loader operation, and 6-month intervals thereafter re-torque all mounting kit bolts. (See below for proper bolt torques) Bolt Torque Chart: (Side plate part of mounting kit) Mount kit bolts Loader mount plate (part of mtg. kit) Standard Metric ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM 0.25 6 7 8 11 12 16 6 3.1 4.3 7.3 9.9 10.3 14 12.1 16.5 0.313 11 ...

Herunterladen

Geben Sie zwei Ziffern: