Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
You and your Maximaid are going to make a great team together. But first it will pay if you really get to know each other. This book will tell you all you need to know about your machine, what it will do and how to do it. Please read all the instructions carefully before operating the machine. Installation Packaging All packaging must be removed from the machine. Transport fittings The wash drum is secured during transport to prevent damage. Before using the machine, remove the transport fittings as follows: 1. Using a suitable spanner, loosen the four transport bolts ( C ) by turning them in an anti-clockwise direction until the bolts can be partially withdrawn. 2. Remove the bolts and the rubber bushes by pulling outwards. An up and down action together with a little dishwashing liquid will ease the removal. 3. Insert the plastic plugs ( P ) supplied with the machine into the holes vacated by the transport fittings. Note: To prevent damage, the machine should be transported with the transport fittings securely in place. Note: Never place the machine on a carpet. This could prevent air circulation and cause electrical components in the machine to overheat. Page 2 Levelling 1. The machine must stand firmly on the floor. Any instability will negatively affect its performance. 2. The machine has two adjustable feet at the front. 3. To level the machine, loosen the plastic lock nuts on the adjustable feet. 4. Rotate the feet until the machine stands firm and level. 5. Tighten the lock nuts firmly. 6. Caution : Never remove the lock nuts and feet from the machine. Connecting to the cold water supply 1. The water supply should deliver 8 to 80 litres per minute. 2. Sealing washers are supplied and these should be fitted at either end of the inlet hose. 3. Secure the angled end of the inlet hose to the water inlet at the rear of the machine and the straight end to a 3/4 inch BSP cold water tap. 4. Tighten both connections, open the tap and check for leaks. 5. We recommend that the tap be closed when the machine is not in use. Water drainage Draining into a dedicated outlet pipe (A) 1. The outlet pipe must have an inside diameter of at least 40 mm. 2. The end of the pipe must be positioned between 400 mm. and 1000 mm. above floor level. 3. Secure the hooked end of the drain hose into the outlet pipe. Draining into a sink or bath (B) 1. The drain hose may be hooked over the edge of a sink or bath in such a way that the end can not be immersed in the collected waste water. 2. The outlet end of the hose must be between 400 mm. and 1000 mm. above floor level. Please note: The outlet hose must be kept free of kinks or restrictions as these will hinder FLOOR A A B 400 1000 NOT LEVELLED NOT LOCKED LEVELLED AND LOCKED the operation of the machine. Page 3 Electrical connection 1. The power cord must be connected to a 15 amp earthed wall socket 2. Do not connect the machine through a double adaptor. It requires a dedicated power point 3. If the power cord should ever need replacing, use only a genuine cord ( Type ‘X’) available from the nearest Defy Service Centre. The appliance must be earthed and the manufacturer and seller do not accept responsibility for any damage due to incorrect electrical connection. The control panel The detergent drawer l 1. Open the drawer. 2. Place detergent and softener in the appropriate compartment of the dispenser drawer, in accordance with the instructions on the manufacturer’s pack 3. Detergent and additives will automatically be released at the appropriate time during the wash cycle. NOTE: Use only low foam detergents specifically designed for front loading washing machines. (l) Detergent for Pre-wash (ll) Detergent for Main wash (c) Fabric softener (d) Siphon lll 123 456 7 1. Programme selection knob 2. Quick wash 3. Prewash 4. Programme progress display 5. Remaining time display 6. On / Off button 89 7. 8. 9. 10. 11. 12. 13. 10 11 1213 Detergent drawer Door open button Rinse plus Anti creasing Spin speed selection Start / Pause / Cancel button Time delay adjustment button. Page 4 Features Features Quick Wash button Selecting this feature will shorten the wash time for lightly soiled fabrics. Quick wash may be used for cotton and synthetic programmes at temperatures below 60°C. Rinse Plus Selecting this feature will adds an extra rinse to the was cycle. This is particularly useful for removing any residual detergent from absorbent fabrics. Anti Creasing Fewer articles of clothing should be loaded when selecting this function. Which enables special wash and spinning profiles to minimise creasing and wrinkles. This significantly reduces the amount of ironing required afterwards. Spin speed selection The desired spin speed may be selected up to a maximum of 1200 rpm. If you do not require any spinning, select the NO SPIN option. Rinse and Hold Selecting this feature will stop the machine during the final rinse cycle with water in the tub. This prevents drip-dry, permanent press and wool arti...
Dieses Handbuch ist für folgende Modelle:Waschmaschinen - MAXIMAID 720W (2.01 mb)