Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Refer to Programming manual. F232172 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Control Panel, OPL Models Only CHM522N CHM1764C 1 Cycle 1 11 Door Open LED 2 Cycle 2 12 Spin Cycle LED 3 Cycle 3 13 Rinse Cycle LED 4 Cycle 4/Up Edit 14 Add Bleach LED 5 Cycle 5 15 Wash Cycle LED 6 Cycle 6 16 Out-of-Balance Indicator Dot 7 Cycle 7 / Set Up (*) Keypad † (Variable-speed only) 8 Cycle 8/Down Edit 17 High Water Level Indicator Dot 9 START Keypad 18 Medium Water Level Indicator Dot 10 CLEAN FILTER Indicator LED (Active for all C80, and C60 X Voltage ONLY models) 19 Low Water Level Indicator Dot WASH ADD BLEACH RINSE SPIN DOOR CLEAN FILTER NORMAL LIGHT SOIL UNIFORMSHEAVY SOIL STAINED DELICATE HOT HOT HOT HOT HOT HOT WARM COLD START PERM PRESS VISA TM 60C 60C 40C 40C 95C 95C << 30C DOMESTIC MODELS INTERNATIONAL MODELS 1 5 6 7 8 4 10 216 17 18 19 39 11 12 13 14 15 1 5 6 7 8 4 10 216 17 18 19 39 11 12 13 14 15 Figure 4 †Set Up(*) keypad is used in cycle programming in Program Mode. Refer to Programming manual. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232172 Operation Display Indicators Table 1 lists the various displays and what they mean. The operator should become familiar with these machine displays. Display Meaning tESt Diagnostic test cycle selected or enabled SPIn Spin (extract) step SUP1 Supply signal 1 (“S1” output), normally detergent SUP2 Supply signal 2 (“S2” output), normally bleach SUP3 Supply signal 3 (“S3” output), normally softener SdLY Spin coast (motor coasts after high speed extract) CFIL Cold Fill HFIL Hot Fill bFIL Warm Fill (cold + hot) bLCH Control will also light “add bleach” indicator PASS Variable-speed ONLY – balance “PASS” condition; shows in “test” cycle only FAIL Variable-speed ONLY – balance “FAIL” condition; shows in “test” cycle only bAL? Variable-speed ONLY – meaning: “Do you wish to enter balance detection test routine?” CY__ Cycle number (followed by a space and number 1 through highest cycle number) norn Normal agitation selected gEnt Gentle (reduced) agitation selected For Wash speed forward (during test cycle) rEv Wash speed reverse (during test cycle) dISt Variable-speed ONLY – distribution speed (during test cycle) LO Low water level nEd Medium water level HI High water level; also denotes “HIGH” spin speed in variable speed “test” cycle. CEL Display all temperatures in degrees Celsius FAr Display all temperatures in degrees Fahrenheit ___C The first 3 digits are reserved for temperature reading, C indicates “degrees Celsius” ___F The first 3 digits are reserved for temperature reading, F indicates “degrees Fahrenheit” FILL “Fill error” – machine did not fill to programmed water level within 10 minutes; also shows during Rapid Advance mode, refer to Programming Manual door “Door” opened during cycle SHUt/door Machine user must “shut door” of the washer to allow the cycle to begin Table 1 (Continued) F232172 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Table 1(Continued) Display Meaning CAnt/OPEn Control cannot unlock the door COIn Control will interpret both coin inputs as signals from a drop coin meter meaning coins must fall through slot at a certain rate to be counted as valid coins. Con1/dEnO Denomination assigned for coin 1 input (example: .25 would mean a US quarter) Con2/dEnO Denomination assigned for coin 2 input (example: 100 would mean a US dollar) CArd Control will interpret the coin 2 input as a START signal from a card reader with no timing max restriction, meaning the signal can last any amount of time once recognized. USH1 “Wash 1” segment USH2 “Wash 2” segment USH3 “Wash 3” segment USH4 “Wash 4” segment rIn1 “Rinse 1” segment rIn2 “Rinse 2” segment rIn3 “Rinse 3” segment rIn4 “Rinse 4” segment (final rinse) donE Cycle has concluded drAI Drain selected for segment; also indicates in drain step during 2 speed version test cycle and in Rapid Advance. Refer to Programming Manual. ---Flashes for a period of time (for safety) after power up while keeping outputs OFF nodr No drain selected for segment. Machine does not drain for segment. SUP6/S 12 Supply 1 and 2 together EFIL Machine set up for extra fill valve. Valve MUST be installed on machine. “EFIL” displays when programmed for extra fill step. nEFL Machine not equipped with extra fill valve HEAt Machine heat functions enabled in control. Machine MUST be equipped with electric or steam heat capabilities. noHt Machine heat functions NOT enabled in control. “noHt” MUST be selected in set up mode if machine does not have electric or steam heat capabilities. bEEP Beep enabled during supply 2 (bleach) and at end of cycle nobP Beep disabled during supply 2 (bleach) and at end of cycle S-xx Setup/configuration code = xx (xx means setup code) P-yy Factory cycle ID program code = yy (yy means setup code) Adv Rapid Advance, refer to Programming Manual. Erdn Drain count error (depending on model) Table 1(Continued) © Copyright, Allia...