Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
(Refer to Figure 28 for lint filter location.) Cleaning the lint filter is important because a layer or pad of lint on the filter will block the flow of air through the dryer, thus reducing the efficiency of the dryer. The clothes will take longer to dry and energy will be wasted. Motor Overload Protector The motor overload protector stops the motor and shuts the heat off automatically in the event of an overload. After cooling, the overload protector will reset itself. The dryer can be restarted by pressing the PUSH-TO-START button. If the overload protector cycles again, remove the dryer from use and call the service person to correct the problem. Figure 28 40 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 510975 Operation Operation Instructions for Electromechanical Dryers IMPORTANT: Before using dryer unit for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of each dryer drum. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Step 1: Clean Lint Filter Clean lint filter before each use. Step 2: Load Laundry Load clothes loosely into dryer drum. Add fabric softener sheet if desired. Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open. Step 4: Determine Proper Dryer The direction of the arrow indicates which dryer is being used. D360I Figure 32 Figure 30 510975 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 41 Operation Step 5: Set Fabric Selector Select NORMAL for cottons, PERM PRESS for permanent press, DELICATE for sensitive items or FLUFF (NO HEAT) for items that require no heat. NOTE: Always follow manufacturer’s care label instructions. PERM PRESS w DELICATE NORMAL X ^ FLUFF J(NO HEAT) FABRIC SELECTOR D342I Figure 33 Step 6: Start Dryer Metered Models Place coin(s) in slide and carefully push in as far as possible and then pull slide out as far as possible. After IN USE light comes on (indicating start of cycle), press the PUSH-TO-START button. D363I Figure 34 Nonmetered Models Rotate timer knob to desired time setting (up to 60 minutes). Press the PUSH-TO-START button. IN USE light will come on (indicating start of cycle). D773I Figure 35 Remove knits when slightly damp because overdrying may cause shrinkage. Do not tumble dry knit woolens. Should dryer stop before cycle is completed, the motor overload protector may have cycled. Refer to page 40. 42 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 510975 Operation Operation Instructions for Electronic Display Control Dryers IMPORTANT: Before using dryer unit for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of each dryer drum. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Step 1: Clean Lint Filter Clean lint filter before each use. D608I Figure 36 Step 2: Load Laundry Load clothes loosely into dryer drum. Add fabric softener sheet if desired. Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open. Step 4: Determine Proper Dryer The direction of the arrow indicates which dryer is being used. D280I Figure 39 510975 Figure 37 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 43 Operation Step 5: Set Fabric Selector Select NORMAL (High Temp), PERM PRESS (Med Temp), DELICATES (Low Temp) or TUMBLE (No Heat) by pushing touchpad. NOTE: Always follow manufacturer’s care label instructions. To Insert Card Insert card into opening. Follow directions on display. DO NOT REMOVE THE CARD UNTIL DISPLAY READS “Remove Card.” Remove knits when slightly damp because overdyring may cause shrinkage. Do not tumble dry knit woolens. FABRICS AND TEMPERATURES D294I Figure 40 Step 6: Insert Coin(s) or Card To Insert Money Insert coin(s) in coin slot. Check pricing as seen on digital display. If Additional Time Feature is turned on, additional dryer time may be purchased at cycle start or while dryer is running. W387I M330I Figure 42 Step 7: Start Dryer To start dryer, push START pad. To stop dryer at any time, open the door. To restart the dryer, close door and push START pad. Cycle is completed when time remaining reaches 00 minutes. FABRICS AND TEMPERATURES Figure 43 Figure 41 44 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 510975 Operation Indicator Lights INSERT COINS INSERT COINS is lit to prompt the user to insert coins to satisfy the vend price for the chosen cycle. When INSERT COINS is lit, the three digits and decimal point will display the vend price remaining to be satisfied. PUSH START PUSH START is lit whenever the dryer is not in a cycle, the full vend price has been satisfied and the dryer do...