Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
5 58" Fig. 6A Fig. 6B Fig. 6D Fig. 7 Fig. 9 A A B CA A C B A A B Fig. 6C A B 8 ATTACHING LEG INSERTS The lathe is supplied with four leg inserts, one of which is shown (A) Fig. 10. To attach the leg inserts to the pedestals, place one side in the hole provided and gently tap the other side, top, and bottom with a rubber mallet (B) Fig. 10. Attach the Headstock (D) Fig. 11, Tool Rest (E), and Tailstock (F) to the lathe bed (G). Notice the tool and centers storage areas located at (H), and brackets on the pedestals to accept a 2 x 12” shelf (not supplied) (J) Fig. 11. If additional stability is desired, insert a 4 x 4 (A) Fig. 11 into the pedestal base (B) Fig. 11. NOTE: You may have to cut a groove in the 4x4”s to allow the lumber to pass underneath the head of the carriage bolt. Fasten the 4 x 4’s to the floor. A A Fig. 12 D A A B Fig. 13 A B A C C B B H J H A G FA E Fig. 10 Fig. 11 HEADSTOCK SPUR CENTER The spur center (A) Fig.12 is equipped with a No. 2 Morse Taper shank. Insert this shank into the headstock spindle (B). NOTE: Before inserting the spur center (A), clean both the shank of the spur center and the inside of the headstock spindle to remove any grease or debris. To remove the tapered shank spur center (A) Fig. 13 from the headstock spindle (B) Fig. 13, use the knockout bar (C) Fig. 13 (supplied) through the hole (D) in the opposite end of the spindle. IMPORTANT: NEVER DRIVE THE WORKPIECE INTO THE SPUR CENTER WHEN IT IS MOUNTED IN THE HEADSTOCK. See the instructions on setting the spur center into the workpiece in the “OPERATION“ section of this manual under “CENTERING THE WORK.” 9 TAILSTOCK LIVE CENTER The tailstock live center (A) Fig. 14, supplied with your lathe, is equipped with a No. 2 Morse Taper shank. NOTE: Before inserting the live center, clean both the shank and the inside of the tailstock to remove any grease or debris. To remove the live center (A) from the tailstock spindle (B), use the knockout bar (C) Fig. 14 (supplied) through the hole (D) in the opposite end of the spindle. ADJUSTING CLAMPS ON THE HEADSTOCK AND TAILSTOCK The headstock and tailstock can be moved along the lathe bed. A downward push on the handle (A) Fig. 15 (tailstock shown) locks the mechanism, while an upward movement of the handle releases the securing action. The clamps are pre-set at the factory. However, should either need adjusting, use an 11/16” wrench (B) Fig. 15 to slightly loosen or tighten the two nuts (C) Fig. 15 shown here on the tailstock. NOTE: Tighten or loosen both nuts equally. NOTE: Clamp the headstock and tailstock firmly while operating the lathe. TOOL REST The tool rest (A) and tool rest base (B) are shown in Fig. 16. To position the tool rest on the lathe bed, lift the clamp handle (C), move the tool rest base and lock it in place by pushing down on the handle (C). To adjust the tool rest (A) for the correct height, loosen the locking lever (D), move the tool rest (A) up or down and tighten the locking lever (D). NOTE: The locking lever (D) Fig. 16 can be positioned on the left or right side of the tool rest base (B). To reposition the tool rest locking lever (D), unscrew the lever counterclockwise. A threaded hole is provided in the left side of tool rest base (B) to accept the locking lever (D) if desired. NOTE: Clamp the tool rest firmly while operating the lathe. ADJUSTING CLAMP ON TOOL REST To adjust the tool rest clamping action, use a 11/16” wrench to loosen or tighten the single nut (A) Fig. 17. Fig. 14 Fig. 15 Fig. 16 Fig. 17 A B D C A C B A B D C A 10 STARTING AND STOPPING THE TOOL The power switch, located under the safety cover (B) Fig. 18 provides electrical power to the adjustable speed drive. Lift the safety cover (B) and move the switch up to the “ON” position. To turn the power off, push the safety cover (B) down. Fig. 18 shows the switch with safety cover down in the “OFF” position. Fig. 19 shows the lathe in the “ON” position (switch cover (A) up and switch (B) up). NOTE: In case of emergency, immediately push the safety cover (B) down to shut off power. These machines have a circuit that automatically decelerates the spindle once you push the stop button (C) Fig. 22 on the control panel. Although an optional dynamic brake is mentioned in the manual provided with the Baldor Adjustable Speed Controller, Delta does not recommend the use of any optional brake systems on the lathe. Further, DO NOT CHANGE OR ADJUST the controller settings that have been pre-set at the factory. LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock (A) Fig. 20 with a 3/16” diameter shackle inserted through the holes in the switch plate (C) Fig. 19. Fig. 18 B Fig. 19 Fig. 20 A B C B ACTIVATING THE SPINDLE Even though power may be going to the adjustable speed drive, the spindle will not turn until you activate it. 1. Before activating the spindle, tighten and clear all clamps,...
Dieses Handbuch ist für folgende Modelle:Drehmaschinen - 46-755X (1.2 mb)