Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified electrician check the receptacle. GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER Fig. A Fig. B 5 EXTENSION CORDS MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Total Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Ampere Rating Volts 0-6 120 0-6 120 0-6 120 0-6 120 6-10 120 6-10 120 6-10 120 6-10 120 10-12 120 10-12 120 10-12 120 10-12 120 12-16 120 12-16 120 12-16 120 Length of Cord in Feet up to 25 25-50 50-100 100-150 up to 25 25-50 50-100 100-150 up to 25 25-50 50-100 100-150 up to 25 25-50 Gauge of Extension Cord 18 AWG 16 AWG 16 AWG 14 AWG 18 AWG 16 AWG 14 AWG 12 AWG 16 AWG 16 AWG 14 AWG 12 AWG 14 AWG 12 AWG GREATER THAN 50 FEET NOT RECOMMENDED Fig. D-1 FUNCTIONAL DESCRIPTION FORWARD Delta Model LA200 is a compact and stable wood lathe with a powerful 1/2 HP, 1725 rpm motor. This lathe will turn objects up to 10" in diameter over the bed and 6" in diameter over the tool rest base with a maximum distance between centers of 37" with the optional bed extension. NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only. CARTON CONTENTS 1 23 4 5 6 7 8 9 10 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Lathe Tailstock Live Center Knockout Bar Tool Rest Base Spur Center Tool Rest Spacer Face Plate Spanner Wrench 6 UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine. After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. ASSEMBLY For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. ASSEMBLY TOOLS REQUIRED Open-end wrench (supplied) Philips Head Screwdriver (not supplied) ASSEMBLY TIME ESTIMATE The assembly time for this unit is approximately 30 minutes. ATTACHING THE ON/OFF SWITCH To prevent damage to the "ON/OFF" switch, the lathe is shipped with the switch bracket detached. Attach the switch bracket in the upright position. Align the two holes in the switch bracket (A) Fig. 1 with the two holes (B) at the rear of the headstock (C). Attach the switch bracket (A) to the machine with two pan head screws (D) and lockwashers (Fig. 2). ATTACHING THE TOOL REST TO THE LATHE BED 1. Loosen the locking lever (A) Fig. 3. Slide the tool rest base (B) into the channel of the lathe bed (C) Fig. 4. NOTE: If the tool rest base will not slide easily into the channel of the lathe bed, turn the tool rest base over and loosen the locknut (D) Fig. 3. Tighten the locking lever (A) Fig. 4 securely. 2. IMPORTANT: If the clamping action on the tool rest base (B) Fig. 4 is too tight or too loose on the lathe bed, remove the base and turn the nut (D) Fig. 4 clockwise to tighten clamping action, or counter-clockwise to loosen the clamping action. Attach the tool rest base on the lathe bed. A C B D D B A D CB A Fig. 1 Fig. 2 Fig. 3 Fig. 4 7 3. Loosen the locking lever (E) Fig.5 and insert the tool rest (F) in the tool rest base. NOTE: To adjust the height of the tool rest, loosen the loching lever (E). After adjustment, tighten the locking lever. Fig. 5 F E ATTACHING THE TAILSTOCK TO THE LATHE BED 1. Loosen the locking lever (A) Fig. 6, and slide the tailstock assembly (B) Fig. 7 in the channel (C) of the lathe bed. 2. IMPORTANT: If the clamping action on the tailstock (B) Fig. 7 is too tight or too loose on the lathe bed, remove the tailstock and turn the nut (D) Fig. 7 clockwise to tighten the clamping action, or counter-clockwise to loosen the clamping action. Attach the tailstock on the lathe bed and tighten locking lever (A) Fig. 6. Fig. 6 A Fig. 7 B D C ATTACHING THE HEADSTOCK SPUR CENTER TO THE LATHE 1. The supplied spur center (A) Fig. 8 is equipped with a No. 2 Morse Tapered shank (B). It will fit snugly into the headstock spindle...