Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
MENU OPERATIONS MENU OPERATIONS IV. INSTALLATION IV-1.LNB Setting MENU OPERATIONS MENU OPERATIONS The Low Noise Blockdown Converter (LNB) amplifies the signal received by the satellite dish and lowers the frequency of the signal. The signal is then fed from the LNB at the dish via cable to the STB. For the LNB Settings, move the cursor to INSTALLATION item and press button. Then, set the cursor to the LNB Setting item and press button. A. Satellite Name Press the button to display the Satellite List box. The Satellite name list is put in alphabetical order. Select one of the preprogrammed satellites that correspond to the value of the antenna. In other words select one of the already searched services at the first installation. If the desired satellite name is not in the list, then select Others . B. LNB Frequency Select the L.O. Frequency set to antenna. The LNB Frequency of 5150, 9750, 10600, 10750, 11475 MHz or Universal can be selected by using the or button. NOTE: If the Universal LNB is selected, both 9750 and 10600 MHz are supported at the same time, and therefore the 22 KHz tone setting is not required. C. LNB Power Select LNB power ‘ On’ for internal and ‘ Off ’ for external. D. 22 KHz If you are using a 22 KHz tone switch box, make 22 KHz tone switch enable or disable to select LNB or antenna. MENU OPERATIONS MENU OPERATIONS E. 12V Use it if the switch box is controlled by 12V DC. (Non-SCART model only) F. DiSEqC 1.0 The STB is designed to be DiSEqC 1.0 compatible. This allows multiple antennas to be connected to the STB at the same time. If using two or more fixed antennas or LNBs, then it is recommended to use a DiSEqC 1.0 switch. Select from 1 of DiSEqC to 4 of DiSEqC, Mini A, MiniB or Disable according to the option or the configuration of DiSEqC switch box or antenna. G. Channel Search It is used to go to channel search menu directly from LNB setting menu, press button at this item. IV-2. Channel Search MENU OPERATIONS MENU OPERATIONS A. Satellite Name Press the button to display the Satellite List Box. The Satellite name list is put in alphabetical order. Select one of the preprogrammed satellites that correspond to the value of the antenna. If the desired satellite name is not in the list, then select Others. MENUOPERATIONS MENU OPERATIONS MENUOPERATIONS B. Search Mode There are 4 search modes, Auto, Manual, Advancedand SMATV.The Auto mode enables to search using the information the IRD has. On the other hand, there will be a need to know in advance the frequencies and the symbol rates before using the Manualmode. On the Advancedmode, enter the Audio PID, Video PID or the PCR PID. The SMATVmode is used to special purposes on satellite master antenna TV system. C. Frequency Enter the Transponder’s Frequency by using the numeric buttons on your RCU. D. Symbol Rate Enter the Transponder’s Symbol Rate by using the numeric buttons on your RCU. E.Polarization Choose the Type of polarization, either the Horizontalor the Vertical. MENU OPERATIONS F. Network Search This Network Searchmenu can be used if the Search modeis turned to the Manual or Auto mode. If the Network Searchmenu is turned on and the NIT (Network Information Table) is available, the Transponder’s information can be found. G. PID Press button to enter Video/Audio/PCR PID’s. 1) Video PID Insert the Video PID by using the numeric buttons on your RCU. 2) Audio PID Insert the Audio PID by using the numeric buttons on your RCU 3) PCR PID Insert the PCR PID by using the numeric buttons on your RCU. Maximum 16 digits can be entered. 4) SAVE To ensure the above Video/Audio/PCR PID change, press button at this item. H. FTA/ Scrambled Choose your favorable channels among FTA only / CAS only / FTA+CAS. MENUOPERATIONS MENU OPERATIONS I. Start Search... Searches for digital channels after the configuration of the LNB is over. To stop the searching process on the way, press either the button or the button. This menu will be shown as long as the STB is searching for channels. All channels found will be listed in two columns on the screen; with TV channels in one column and Radio channels in the other. Please note that the search procedure may take a few minutes. When the search procedure is completed, the screen will show how many TV and Radio channels have been found. Press button to save the channels. J. LNB Setting To go to LNB Setting menu directly from Channel Search menu,press MENU OPERATIONS button at this item. MENU OPERATIONS IV-3 . Motorized DiSEqC 1.2 If you have DiSEqC 1.2 motorised system, then you can use the DiSEqC 1.2 functions. . Satellite Name A selection of satellite names that will be used to identify a motor position. . Frequency: Selects the frequency to catch the strong signal. . DiSEqC Command Mode : Change the current mode between Userand Installer modes. -User: This mode is used to fine-tune the position of the motor for better reception. -Installer: This mode is used to search for the position of a satellite manually. . ...
Dieses Handbuch ist für folgende Modelle:Sat-TV-Receiver - TF3000FI (2.34 mb)