Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Run wires from the back of the dome unit to the roof edge, then along edge to location where wiring will be fed into the vehicle. (If installing an optional second receiver, run auxiliary coax to location where it will enter the vehicle.) Secure wiring to roof every 12-18 inches (Fig. 10). 12. Drill 3/4” hole through the roof and into the cabinet where receiver is stored. Feed wiring down through hole. Seal opening with roof compatible sealant so that it is entirely waterproof (inside and outside of the 3/4” hole). Repeat for optional second receiver (Fig. 10). Fig. 10 TYPICAL ROOF INSTALLATION - OVERHEAD VIEW IMPORTANT! Sealant must be roof compatible. 13. Remove blue protective sheet and red “position to rear” sticker from the dome unit. Page 9 INTERNAL WIRING IMPORTANT: The connection between the dome unit and the receiver must be a direct connection with no devices in between. Any other devices should be downstream from the receiver. 14. Inside vehicle, connect main coax from the dome unit directly to the “satellite in” port of the main receiver. Do not go through an “A-B” or any other switch, box, or booster. Connect auxiliary coax directly to optional second receiver. IMPORTANT: Power connection must be a non-shared circuit. Excessive current draw on the circuit will cause the unit to operate improperly. Power and ground connections must be made after the wires are connected to the dome unit. 15. Connect red and black two conductor wire to a power source and ground. Red connects to +12 volts, and black connects to ground. 16. Plug phone style Controller Cable into Controller. Page 10 SECTION 4 OPERATION IMPORTANT! There must be a clear “line of sight” to the southern sky. Mountains, buildings, trees, telephone poles, etc. can all block the satellite signal from reaching the dish. 1. Turn TV and satellite receiver on. 2. Go to the signal meter screen on TV. Choose transponder number: Dish Network #11 DIRECTV #19 3. Enter local ZIP code on signal meter screen to determine satellite elevation. If you do not know your local zip code, determine your elevation from the maps on pages 12-14. 4. Press and hold UP/ON arrow on King-Dome Controller for 3 FULL SECONDS to turn King-Dome on. Note: The Controller will flash a series of codes and then display its elevation. Wait for the Controller to steadily display the elevation before continuing (about 10 seconds). 5. Press UP or DOWN arrow on King-Dome Controller to match elevation on Controller to elevation on TV signal meter screen or elevation from maps on pages 12-14. IMPORTANT! In Step 6, as soon as you begin holding the right arrow, you must continuously monitor the TV signal meter screen until signal appears on TV. 6. Press and hold RIGHT arrow until Controller begins RAPIDLY flashing its clock position (7-10 seconds). (See Fig. 2, Page 3.) Remember, you must watch for signal strength on TV! Dish will automatically perform a 360 degree scan for satellite. When signal strength appears on TV, press ANY BUTTON to stop the dish from rotating. 7. Press the UP, DOWN, LEFT or RIGHT arrows to fine tune signal strength to the highest possible number on TV signal meter screen. Enjoy your programming! Page 11 Elevation Map for DIRECTV 101 Find your location on the map. Use the elevation lines to determine your approximate elevation. Page 12 Elevation Map for Dish/DIRECTV 110 Find your location on the map. Use the elevation lines to determine your approximate elevation. Page 13 Elevation Map for Dish/DIRECTV 119 Find your location on the map. Use the elevation lines to determine your approximate elevation. Page 14 While the dish rotates, the direction of the dish in relation to the vehicle’s position will be displayed on the controller as a clock number. (The windshield is always 12:00 o’clock: see Fig. 2, Page 3.) This information can be used to determine when the dish is close to pointing at the desired satellite. IMPORTANT! You must continuously monitor the TV for signal strength while the dish is rotating. DO NOT WATCH THE KING-DOME CONTROLLER. Page 15 SECTION 5 STORE/RECALL POSITIONS Note: For use with multi-satellite services. (such as Dish 500) Page 16 Store Satellite Position #1 1. Once locked onto a desired satellite, hold LEFT AND RIGHT arrows simultaneously until display flashes. 2. Hold LEFT arrow until 1P (Position 1) appears on display. Position #1 is stored in memory for this position. Store Satellite Position #2 3. Once locked onto the second desired satellite, hold LEFT AND RIGHT arrows simultaneously until display flashes. 4. Hold RIGHT arrow until 2P (Position 2) appears on display. Position #2 is stored in memory for this position. Recall Satellite Position #1 5. Press DOWN AND LEFT arrows simultaneously. Dish will automatically move to Satellite Position #1 and controller will display 1P. Recall Satellite Position #2 6. Press DOWN AND RIGHT arrows simultaneously. Dish will automatically move to Satellite Position #2 and controller will display 2P. ...
Dieses Handbuch ist für folgende Modelle:Sat-TV-Receiver - 9630 (1.07 mb)