Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Nokia Dateigröße: 1.55 mb Dateiname: Unterrichtssprache:

(“YES” is the default setting). Select “NO” to search only from the transponder that you have entered on line “Transponder Frequency”. (Useful if you do not want to search through all transponders for a specific Programme Distributor). By pressing the OK button you can now enter the menu from where the Mediamaster starts to search for channels from the satellite. SMATV or IF frequency channel search Model 9200 S only A SMATV network is commonly found in smaller block of flats. In such a network you will have access to a central antenna system. If the Mediamaster is connected to a SMATV network, select “SMATV or IF frequency search”. Pressing the OK button will give a menu where you can enter different values for “Symbolrate” and “FEC”. However, the most common alternatives for “Symbolrate” and “FEC” are already preprogrammed. (You only have to make changes here in exceptional cases). Just press the OK button once again, and the “Channel Search” procedure will start; Refer to “Channel Search” on page 12. GB 15 Important general information Viewing TV Important general information Viewing TV The following will describe the basic functions of your Media- master during the watching of TV or listening to Radio channels from the Mediamaster. Sometimes the information may not be displayed as illustrated. Many of the functions described here are dependent on the Service Provider and/or can only be used if they are included in the transmitted programme information. Please note, that during the Channel Search procedure, the Mediamaster has downloaded ALL available channels. This may include channels from various Service Providers, also those to which you normally do not have access, (unless you have a Smart Card from one of those Service Providers). If you select a programme to which you do not have access, you will get the message “No Smart card” on the screen. Start/stop watching TV To start the Mediamaster from stand-by mode, press the button, TV button or one of the number buttons on the remote control. It is also possible to start by pressing the button behind the lid on the front of the Mediamaster. Put the Mediamaster into stand-by by pressing the button. In stand-by mode the display will show the correct time. Select Channel Change channel with the numbered buttons or with the up/down buttons on the remote control. You can also use the buttons on the front panel of the Mediamaster. Programme Information. The “ “ Button Every time you change channel you will receive information for 4-5 seconds about the current programme. This information includes: Channel number, name, title and time. Press “i” while watching a channel. If your Service Provider trans mits programme information you will see: Correct time; A small amount of information for the current and next programme. (Alternate between “Now” and “Next” with the left/ right buttons); Name and number of the channel; Finally the start and stop time for the programme. GB 16 From here you can also obtain information about other channels. Select with the up/down buttons. If you stop on another channel number and press OK, you will exit the menu and return to TV mode, but now on the new channel. If you select “Next” on a programme line and press set a “Reminder” OK, you will . This means that, while watching TV, you will be reminded when the “Reminder marked” programme starts. If you press the “i” button once more, you will get extended information (if transmitted) for the current or next programme. To exit the menu, press the TV or “i” button. TV Guide By pressing the GUIDE button you obtain access to the TV Guide which will give the titles of the present programme on the different channels. By pressing the Left or Right button you also can obtain information for the next programme. Use the Up/Down buttons to move the cursor to different programme areas. You can obtain extended information for a programme by pressing the “i” button. If you select “Next” on a programme line and press OK, you will set a “Reminder”. This means that, while watching TV, you will be reminded when the “Reminder marked” programme starts. Please note, that these features will only work if they are included in the transmission from the Service Provider. The Radio button Pressing the button once gives you a menu where you can change the spoken language in the present TV programme. (Only if more than one language is transmitted). Pressing the button twice will lead to the specific Audio Channel mode. The display on your Mediamaster and on the TV screen will show the name of the audio channel you are listening to. While in audio mode, you can press the “i” button to get extended information (if transmitted) about the audio programme. Return to TV mode by pressing the TV button or again. GB 17 Volume level Volume level Increase or decrease the sound level by pressing the “+” and “-” buttons. A control bar will be displayed on the screen during level adjustment. (The max. level for volume is th...

Herunterladen

Geben Sie zwei Ziffern: