Stimmen - 6, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If you set it to 2(E), the antenna will move to the east by two degrees. At this time 30 Service Search you had better check the receiving quality of every transponder and choose the best one at the Transponder (or Frequency) option. It will be helpful to your fine tuning. 5. Finally set the Motor Control option to Store to save the tuned position when the receiving quality is best. There are more motor control options for installers, but this guide does not describe them. If you are an installer, refer them to the manual about the STAB rotor. 4.1.3 Configuring USALS settings USALS (Universal Satellite Automatic Location System), also known as DiSEqC 1.3, calculates the positions of all available satellites from your location. Compared to DiSEqC 1.2, it is no longer required to manually search and store every satellite position. Just pointing to a known satellite position is enough. This position will act as a central point. The USALS will then calculate positions of visible satellites. To use the USALS protocol, select the Installation > USALS Setting menu. You should see a screen like the left figure. At first you have to set the Motorized DiSEqC 1.3 option to Enable. To get every satellite position calculated, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 4.1 Searching broadcasting services 31 2. Enter your location to the My Longitude option and the My Latitude option with the . ... .. V. , V+ and numeric buttons. 3. Enter the position of your selected satellite to the Satellite Angle option if it is not correct. 4. Select the Goto the position option; then the antenna will turn toward your selected satellite as calculating its position. 5. If the receiving quality, which is displayed at the bottom right of the screen, is not good, then tune the antenna finely with the Move option. The changed position is automatically saved. At this time you had better check the receiving quality of every transponder and choose the best one at the Transponder (or Frequency) option. It will be helpful to your fine tuning. 4.1.4 Searching services To perform service search, select the Installation > Service Search menu. You should see a screen like the left figure. There are four service search methods: • Searching every service of a satellite. • Searching every service of a transponder. • Searching one service of a transponder. 32 Service Search • Searching every service of a SMATV (Satellite Master Antenna Television) system. Searching every service of a satellite To search every service of a satellite, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to Auto. 3. If you set the Network Search option to On, the digital receiver will check up the up-to-date channel information as searching services, but it takes rather longer time. Searching every service of a transponder To search every service of a transponder, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to Manual. 3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons. 4. Enter the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons. 5. Set the Polarization option to the polarization of your desired transponder. 6. If you set the Network Search option to On, the digital receiver will check up the up-to-date channel information as searching services, but it takes rather longer time. 7. Set the Modulation option to the modulation type of your desired transponder. If your desired transponder has high definition broadcasts, you should set this option to DVB-S2 QPSK or DVB-S2 8PSK. Then the FEC option 4.1 Searching broadcasting services 33 and the Pilot option will become enabled. You also should set these options correctly. NOTE You may get transponder information from a satellite magazine or website such as or lyngsat.com. Searching one service of a transponder To search one service of a transponder, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to Advanced. 3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons. 4. Enter the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons. 5. Set the Polarization option to the polarization of your desired transponder. 6. Specify the packet identifiers of your desired service at the PID option with the numeric buttons. A packet identifier is used to verify audio and video streams. Searching every service of SMATV system To search every service of a SMATV system, if the digital receiver is connected to it, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to SMATV. 3. Choose your desired transponder at th...
Dieses Handbuch ist für folgende Modelle:Sat-TV-Receiver - TF 7710 HSCI (1.17 mb)