Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Topfield Dateigröße: 1.23 mb Dateiname: Unterrichtssprache:

28 Service Search 4.1.2 Configuring DiSEqC 1.2 settings Your motorized antenna will turn towardyour desired satellites horizontallyby DiSEqC 1.2. When you switch to an service, if the service is provided by a satellite other than current one, it will take longer time than usual because the antenna has to turn to its position. To use DiSEqC 1.2, select theInstallation > Motorized DiSEqC 1.2 menu. At first you have to set the Motorized DiSEqC 1.2 option to Enable. To get the correct position of your desired satellite, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the DiSEqC Command Mode to User. 3. Select the Goto option at the Motor Control menu. Then the antenna will turn towardyour selected satellite with the position data that the digital receiver has. 4. If the receiving quality, which is displayed on the right bottom on the screen, is not good, tune the antenna finely with the options of the Movement menu. If you select 4.1 Searching broadcasting services 29 the 2(E) movement option, the antenna will move to the east by two degrees. At this time you had better check the receiving quality of every transponder and choose the best one at the Transponder (or Frequency)option. It will be helpful to your fine tuning. 5. Finally select the Store option at the Motor Control menu to save the tuned position when the receiving quality has turned good. There are more motor control options for installers, but this manual does not describe them. If you are an installer, refer them to the manual for the STAB rotor. 4.1.3 Configuring USALS settings USALS (Universal Satellite Automatic Location System), also known as DiSEqC 1.3, calculates the positions of all available satellites from your location. Compared to DiSEqC 1.2, it is no longer required to manually search and store every satellite position. Just by pointing to a known satellite position is enough. This position will act as the central point. The USALS will then calculate positions of visible satellites. To use USALS, select theInstal lation > USALS Setting menu. At first you have to set the Motorized DiSEqC 1.3 option to Enable. Tocalculate every satellite position, perform the following steps: 30 Service Search 1. Choose your desired satellite at the Satellite Name option. 2. Input your location to the My Longitudeand My Latitude options with the . ... .. V. , V+ and numeric buttons. 3. Input the position of your selected satellite to the Satellite Angle if it is not correct. 4. Select the Goto the position option. Then the antenna will turn toward your selected satellite calculating its position. 5. If the receiving quality, which is displayed on the right bottom on the screen, is not good, then tune the antenna finely with the options of the Move menu. The changed position is automatically saved at one. At this time you had better check the receiving quality of every transponder and choose the best one at the Transponder(or Frequency)option. It will be helpful to your fine tuning. 4.1.4 Searching services To perform service search, select the Installation > Service Search menu. There are four service search methods: • Searching every service of a satellite. • Searching every service of a transponder. 4.1 Searching broadcasting services 31 • Searching one service of a transponder. • Searching every service of a SMATV (Satellite Master AntennaTelevision) transponder. To search every service of a satellite, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to Auto. To search every service of a transponder, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to Manual. 3. Choose your desired transponder at the Frequencyoption or input it with the numeric buttons. 4. Input the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons. 5. Set the Polarizationoption to thepolarization of your desired transponder. NOTE You could get the transponder information from a satellite magazine or web site such as or To search one service of a transponder, perform the following steps: 1. Choose your desired satellite at the Satellite Name option. 2. Set the Search Mode option to Advanced. 32 Service Search 3. Choose your desired transponder at the Frequencyoption or input it with the numeric buttons. 4. Input the symbol rate of your desired transponder to the Symbol Rate option with the numeric buttons. 5. Set the Polarizationoption to thepolarization of your desired transponder. 6. Specify the PIDs of your desired service at the PID menu with the numeric buttons. PID (Packet Identifier)isa set of numbers that identifies transport stream packets. To search every service of a SMATV transponder, if the digital receiver is connected to a SMATV, perform the following steps: 1. Choose your desired satellite...

Herunterladen

Geben Sie zwei Ziffern: