Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Motorola
Dateigröße: 482.63 kb
Dateiname: 6f580d1e-4712-4042-9ccd-96372e7556c4.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
(The LED will not be lit while the ^ keys are depressed. - While pointing the remote control at your TV (or VCR), press the .A. key to scan upward to the next code. (Use the ~w key to return to the previous code.) - If the transmitted code is the correct one, your TV (or VCR) will turn off, responding as if its POWER key were pressed. - If your TV (or VCR) does not respond, depress the A. key to try the next code. When your TV (or VCR) turns on or off as a result of the transmitted code, you will know that you have found the correct code. - When you have found the correct code (power to your TV or VCR is toggled on or off), press the ENTER key. This will store the manufacturer’s code. The LED will then flash rapidly several times and turn off. NOTE: If your TV is not listed in the tables and/or the codes for your brand are not accepted by the remote, you will need to use the remote originally manufactured for your unit. Programming the Master Power Feature If you wish to control the power on/off function of your satellite receiver, VCR, TV, and all connected equipment with a single press of the POWER key on your remote control, you can enable (or disable) the remote control’s Master Power feature by following these steps: • Press the SAT key on the remote control for at least three seconds or until the light on the key blinks. • Press the POWER key on the remote. The light will remain on steady. Press the power key a second time, and the light on the remote will blink on and off briefly, which indicates that the remote has accepted the Master Power command. DSR405 User Guide 5 Verifying Your TV, VCR and AUX Mode Codes You can verify the accepted programming codes for each mode by following these steps. 1. Press the TV, VCR, AUX key for at least three seconds or until the LED blinks. 2. Press the "INFO" key. 3. The LED will blink, indicating the code of your TV, VCR or auxiliary component in the following sequence. For example, if your TV code is for a Tandy brand TV (code 105) the blink pattern will be: - Pause>long blink "1;" - Pause>short blink "0;" - Pause>long blink, long blink, long blink, long blink, long blink "5." A zero in the code will always be represented by a short blink. 4. For the AUX mode only, after the code is verified the appropriate mode key will blink to indicate the component being controlled. If You Have More Than One Satellite Receiver Ifyou have more than one satellite receiver, you may want to prevent the remote controls from affecting the other receivers. To prevent this kind of interference, you must "pair" each remote control with one receiver. In order to do this, you will have to assign a new "address" to each pair of remote controls and receivers so that each pair functions independently of the others. If you have two or more receivers, see Chapter 10 for information about the procedure for changing addresses. 6 Using Your Remote Replacing the Remote Control Batteries When the remote control batteries are worn out (discharged), the remote will stop working. Replace the batteries as soon as possible to retain your programmed codes. Once you remove the batteries from the compartment, you must replace them within two hours to retain your programmable features. The remote control for this unit may be powered by two AA batteries. Use only high quality, noncorrosive batteries designed for use in electronic equipment. Remember to replace both batteries at the same time. To replace the batteries: - Remove the cover by pressing down the back panel indentation and removing the panel off the remote control. - Position each battery in the battery compartment so that the flat base (-) is against the spring and so that the raised contact (+) is against the terminal. Make sure the batteries are securely seated. - Replace the cover. "Remote Energy Saver” If you misplace your remote (i.e., it is stuck in your couch), and a key is inadvertently pressed, the remote will automatically turn itself off after three minutes. TV Codes (To program AUX, press TV mode key) Admiral.................................................................. 018,090,125 A-Mark................................................................... 120,224,225 Aiwa........................................................................ 090,251 Akai..............................................................000,032,070,149,172 Amstrad.........................................................................033 Anam......................................................... 005,009,021,041,120,121 Anam National....................................................................211 AOC................................................... 005,006,019,020,120,140,163,173 Archer...........................................................................120 ASA............................................................................047 Audio Dynamics........................................