Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Philips, modell SDV2927

Hersteller: Philips
Dateigröße: 284.31 kb
Dateiname: 4dac9545-16b1-6af4-7d11-b712be1913e0.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Take the time to plan your installation procedure. Do all assembly work on the antenna on the ground. Raise the completed antenna after assembly. Do NOT work on a wet, snowy or windy day or if a thunderstorm is approaching. Do NOT use a metal ladder. If the antenna assembly starts to fall, get away from it and let it fall. Remember that the antenna mast and cable are all excellent conductors of electrical current. Do NOT install the antenna by yourself. Be sure that there are two other people available for help. If any part of the antenna should come in contact with a power line . . . DON'T TOUCH IT OR TRY TO REMOVE IT YOURSELF. Call your local power company immediately.They will remove it. Should an electrical accident occur . . . DON'T TOUCH THE PERSON IN CONTACT WITH THE POWER LINE,or you too can become electrocuted. Instead, use a DRY board, stick, or rope to push or pull the victim away from the power lines and antenna.Once clear, check the victim. If he has stopped breathing, immediately administer cardiopulmonary resuscitation (CPR) and stay with him. Have someone else call for medical help. Install wire antennas high enough that they will not be "walked into" by people. Do not install antenna wire(s) over or under utility lines. Important Information Important installation information The SDV2940 uses a power injection module to power the antenna amplifier. It is essential for proper operation of this antenna system that the amplifier be connected between the antenna and any devices such as splitters, matching transformers, networks, etc. SEE DIAGRAM TO LEFT. Disregarding this important notice may result in damaging the power injector or improper operation / poor performance. SDV2940_27_manualV3.qxd 5/5/08 4:01 PM Page 5 SDV2940_27_manualV3.qxd 5/5/08 4:01 PM Page 5 ENParts Included 1. SDV2940 Antenna. . . . . . . . . . . . . . . . . . . . . . 1 2. Power supply 120V to 6VDC . . . . . . . . . . . . 1 3. Wall / Mast Bracket. . . . . . . . . . . . . . . . . . . . 1 4. Nuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. U-Bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6. Mast clamps . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7. Nuts with lock washers. . . . . . . . . . . . . . . . . 4 8. L-Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9. 2" Wood Screws. . . . . . . . . . . . . . . . . . . . . . . 4 10.20' coax cable with connectors. . . . . . . . . . . 1 11.Weather Boot. . . . . . . . . . . . . . . . . . . . . . . . . 1 12.Power Injector . . . . . . . . . . . . . . . . . . . . . . . . 1 13.Plastic Anchors. . . . . . . . . . . . . . . . . . . . . . . . 4 Mounting Instructions fig.1 fig.2 Wall Mount Determining signal strength Before Installation determine the best location for optimum reception. It is important for the antenna to have an unobstructed path to the transmitter.To determine the transmitter(s) location you can consult the website For best results the antenna should be facing the transmitter location. For indoor wall mount installation: NOTE: Do all antenna assembly work on the ground before installing on a wall or an antenna mast. 1. Attach main body to the L – bracket as shown, using cross head screw note the orientation of the bracket. Do not fully tighten the screw to allow for later adjustment (fig. 1). 2. Using the Wall/Mast bracket as a guide, mark position for the four 2” wood screws. If possible locate a stud to screw into. If a stud is not available, use appropriate wall anchors (not included, available at any hardware store) (fig. 2). 5 SDV2940_27_manualV3.qxd 5/5/08 4:01 PM Page 6 SDV2940_27_manualV3.qxd 5/5/08 4:01 PM Page 6 EN Mounting Instructions fig.3 fig.4 fig.5 fig.6 3. Attach the main body and L-bracket to wall / mast mounting bracket using cross head screw (fig. 3) note the orientation of the bracket. ) Do not fully tighten this screw to allow for later adjustment (fig. 3). 4. Tighten all screws and nuts to firmly affix the antenna to the wall. 5. Attach the cable to the F connector on the underside of the unit and weather protection boot over the connection. See next steps under – Connections to your TV For outdoor mast mount installation: NOTE: Do all antenna assembly work on the ground. Raise the completed antenna after assembly. 1. Insert U-Bolts into the holes of the wall/mast bracket (fig. 4). 2. Slide the mast clamps onto the U-Bolts (fig. 4). 3. Attach the 4 nuts with lock washers to the U-Bolts - do not tighten fully (fig. 4). 4. Slide the assembly on to the mast. Do not tighten fully, just snug enough for the assembly to stay in place (fig. 5). 5. Attach the L-Bracket to the wall / mast bracket using cross head screw and nut, Note the orientation of the bracket. Fully tighten this screw. 6. Attach the main body of the antenna to L bracket vertically. 7. Tighten all screws and nuts to firmly affix the antenna to the mast. 8. Adjustment of the antenna direction will ...