Stimmen - 7, Durchschnittliche Bewertung: 2.9
(
)
)
|
Anleitung Zusammenfassung
1. Press the buttons to display the satellite list box. 2. Select the wanted Satellite Name. 3. If the desired Satellite Name is not listed then select User Defined. 4. The keyboard will appear and you can type the Satellite Name directly. The selected Satellite Name can help you select the Antenna Alternative in the searching menu, but it is possible to change or select the Satellite Name only in the Antenna Setting menu. Note: In case the selected satellite is used as OTA target satellite, automatic detection of the OTA target satellite might not work properly if you change or edit the name of the satellite. 5. Satellite Name is listed in alphabetical order and the order can be changed according to Menu Language. 6. When inputting the Satellite Name, there is a 14 character limit. LNB Frequency 1. Select the L.O. Frequency that is set to antenna. 2. Use the buttons to select the LNB frequency(Universal, 5150, 9750, 10600, 10750, 11475MHz or 0, 1, ......., 9). 3. If the required LNB Frequency is not available, then select “0” and enter the frequency manually using the Numeric buttons(0~9). 4. When you select Universal, both 9750 and 10600MHz are supported at the same time. The 22KHz Tone setting is unnecessary. (Disabled) E25 22KHz Tone When you use a dual LNB or two antennas connected to a 22KHz Tone switch box, make 22KHz Tone switch Enable or Disable to select LNB or antenna. DiSEqC Input According to the option and position of DiSEqC switch, select Disabled, Tone Burst A to B and DiSEqC A to D. After setting the above mentioned value, press the OK button to move to the Manual Search menu. Motorised System The Motorised System is used to set the DiSEqC 1.2 motor by Eutelsat specification. If you wish to use this system, please refer to page E33. Service Search OSD 1. If you press the EXIT button during the search, then Service Search stops and the searching menu will appear again. 2. When you find all the services, the following picture appears. 3. Before saving it, you can select the services you want to delete. Found services OSD 1. The picture above shows services that are found after Manual Search. 2. Use the Red( )button to mark the services that you want to delete. To unmark a service, select the service and press the Red( ) button again. 3. Press the OK button to save or press the EXIT button to exit without saving. 4. Then Service Search menu appears again. When you exit from all menus, the first service of the found service list is played. In the bottom of found service picture, network, the information of transponder and the number of found service that the services belong to are displayed. The deleted service by the Red( ) button is excepted from counting of the number of services. The deleted service is not included in this number. “Free” applies to the empty space of the memory. It will be used to store future services. E26 Guide of Main Menu Manual Search Set the search parameters(Frequency, Symbol Rate, etc.) to manually find the services that you have selected in the transponder. The bar on bottom of the submenu shows the signal Level and signal quality(BER) of the entered parameters. Antenna Alternative Select the target antenna for Manual Search. The Satellite Name helps you select antenna alternatives. This is only for reference and cannot be changed on this menu. Antenna Alternative 16 is fixed for SMATV. Frequency Use the Numeric buttons(0~9) on the remote control unit. Polarisation Use the buttons to select the Polarisation of the transponder. (Auto, Horizontal, Vertical) • Horizontal : 18 V is output through LNB line • Vertical : 13.5 V is output through LNB line Symbol Rate Input the Symbol Rate of the transponder you want to find. Use the buttons or Numeric buttons(0~9) on the remote control unit. FEC(Forward Error Correction) Use the buttons to select the Forward Error Correction of the transponder. You can select the value of Auto, 1/2, 2/3, 3/4, 5/6 and 7/8. E27 Network Search • You can select Yes or No. When you select “Yes”, you can find more transponders using the home network. • As it refers to NIT during searching, if there is the frequency information of other transponder, it searches the other transponders besides the transponder that the user inputs. Automatic Skip • You can select Yes or No. When you select “Yes”, the search will skip all scrambled services. • When the found services are scrambled during searching, they are not listed up. Refer to descriptor of PMT whether it is scrambled or not. Advanced... Performs a manual search with the ability to enter PID(Video/Audio/ PCR) values. This mode is necessary when you search for the signal that has abnormal service Information tables. The setting of the sub items is the same as Manual Search. Video PID/Audio PID/PCR PID You can set PID to search for services. 1. Use the buttons to select PID input mode. 2. Use the Numeric buttons(0~9) on the remote control unit to enter a decimal PID value. 3. In the hexadecimal inp...