Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
MAINS SUPPLY : 190 - 250 V AC 50/60 Hz OVERLOADING : Do not overload a wall outlet, extension cord or adapter as this may result in fire electric shock. LIQUIDS : The STB shall not be exposed to dripping or splashing and that no objects filled with liquids, such as base, shall be placed on the apparatus. CLEANING : Disconnect the STB from the wall outlet before cleaning. Use a light damp cloth(no solvents) to dust the STB. VENTILATION : The slots on top of the STB must be left uncovered to allow proper airflow to the unit. Do not stand the STB on soft furnishings or carpets. Do not expose the STB to direct sunlight or do not place it near a heater. Do not stack electronic equipments on top of the STB. ATTACHMENTS : Do not use any unrecommended attachments as these may cause hazard or damage the STB. CONNECTION TO THE SATELLITE DISH LNB : Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish. FAILURE TO DO SO CAN DAMAGE THE LNB. CONNECTION TO THE TV : Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish. FAILURE TO DO SO CAN DAMAGE THE TV. EARTHING : The LNB cable MUST BE EARTHED. The earthing system must comply with SABS 061. LOCATION : Place the STB indoor in order not to expose to lightening, rain or sunlight. E2 Copyright & Glossary Copyright & Glossary Copyright • VIACCESSTM is a trademark of France Telecom. • CryptoWorks(TM) is a trademark of Philips Electronics N.V. • Irdeto is a trademark of Mindport BV. • Nagravision is a registered trademark of Kudelski S.A. • Conax is a trademark of Telenor Conax AS. • “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Warning HUMAX cannot be held responsible for any kind of problems caused by the use of unofficial software. The use of software versions other than HUMAX official software will void the manufacturer’s warranty. It is advised that only the formal software released from HUMAX should be used in all HUMAX product range. Glossary • Antenna A divice that collects and radiates electromagnetic waves. Includes a satellite dish and abroadband antenna. • Forward Error Correction(FEC) A system of error control for data transmission. • Frequency The number of cycles or events per one second, which is expressed in the unit of Hertz(Hz). • Intermediate Frequency(IF) A frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception. • Low Noise Block(LNB) Downconverter A low noise microwave amplifier and converter which downconverts a range of frequencies to IF range. • Packet Identifier(PID) A set of numbers that idenitifies transport stream packets containing data from a single data stream. • Polarisation Characteristic of an electromagnetic wave determined by the orientation of the electricfield vector. • Quaternary Phase Shift Keying(QPSK) Phase-shift keying in which four different phase angles are used. • Service A channel to which a decoder or TV is tuned. • Transponder An automatic device that receives, amplifies and retransmits a signal on a different frequency. E3 Reference 1. Connect DiSEqC 1.0 All our receivers are designed to be DiSEqC 1.0 compatible. This allows multiple antennas to be connected to the STB simultaneously. If you have two or more fixed antennas or LNBs, you can use a DiSEqC 1.0 switch. 1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch. 2. Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input connector of the DiSEqC switch. 3. Do the same for other LNBs. 4. Connect one end of a Coaxial cable to the RF output connector of the DiSEqC switch and the other end to the LNB IN socket on the STB. 2. Connect DiSEqC 1.2 Please refer to page E36. 3. Connect a Satellite antenna To the digital receiver, you can connect either a single satellite antenna directly or through converter box several antennas or LNB of multi-feed equipment. You can connect a further Sat-receiver(for example analogue), with the receiver of common antenna equipment that has satellite signals. • Connect an antenna cable through converter boxes 1. When you assemble several antenna or a multi-feed equipment that has several LNB (or LNB with several exits), connect each cable from the antenna to a converter box. 2. Connect the output of converter box to “LNB IN”, as in example displayed. 3. When you use a converter box of 0/12V-steerage, connect it to the output “0/12V” additionally. For converter boxes of 22KHz- or DiSEqC-steerage, you can skip this point because the steerage signal occurs through the antenna cable. 4. Loop Through If you have another analogue or digital STB and you wish to use the same LNB then you can connect it via the loop through. Connect one end of a Coaxial cable to the LNB OUT on the STB and connect the other end to the LNB IN on your second STB. E4 Reference 5. Connect a S/PDIF Fiber-Optic cable If you are watching a progra...