Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
PATENT NO. 5,532,710 AND 5,554,998 Made in U.S.A. INSTALL “FRONT” INSCRIBED ON BASE TOWARD FRONT OF VEHICLE! PARTS INCLUDED: Reflector (dish) Gasket RS-1000 antenna Interior parts Mount/base assembly Hardware Models RM-DM61/DM55 Electronic elevation sensor Models RM-4610/DM61 Power supply Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 319/754-0600 • FAX 319/754-0787 • 2451070 Rev. 12/21/05 FINDING THE SATELLITE STEP 1. Step outside the vehicle and, using a compass, determine which direction is North. (Standing in or near the vehicle can give you an incorrect reading.) The more accurately you determine North, the easier it will be to find the satellite(s). STEP 2. Using satellite receiver, determine correct elevation for your location. See your receiver manual for setup information. STEP 3. Press button on Winegard Digital Display wall plate. If the antenna is in travel position, the display will show LL for Low Limit. HL for High Limit will show when dish is in Up position. STEP 4. Crank elevation handle to raise antenna. Stop cranking when readout displays the correct elevation for your location. STEP 5. Rotate antenna VERY SLOWLY until correct satellite signal is acquired. NOTE: Rotate 3° and then stop. DO NOT rotate continuously, even if you are rotating slowly. If you notice the elevation angle has changed, it may be due to the following reasons: a. RV is not parked level. b. Antenna system is mounted to a slightly sloped RV roof. (This is not a problem. When you have rotated the antenna so it is facing in approximately the right azimuth [compass direction], simply adjust to correct elevation and continue searching for the satellite signal.) Special notes: When you have detected the satellite signal, adjust the antenna up/down and left/right for the strongest signal your receiver displays. Because of differences in receivers and installation methods, you may find the elevation numbers, after peaking on the strongest signal, no longer match what the receiver recommended. This is normal. The elevation sensor should always get you close enough to find a signal to peak on. If display turns off while you’re searching, just push button for another minute of operation. After a little practice, most people can find the signal in 30 to 50 seconds. TROUBLESHOOTING • If digital display reads EE, check wiring and connection. If wiring and connections are not correct at installation, operation is affected. • Remember to rotate antenna VERY SLOWLY until correct satellite signal is acquired. DISPLAY CODES HL..................High Limit LL .................. Low Limit Lo..................Battery Low Er..................Communication Error ................Initializing NOTE: Initialization may take up to 5 seconds. Based on 5 minutes a day of usage, standard new alkaline batteries should last 88 days. 2 OPERATION TUNING ANTENNA FOR THE BEST PICTURE STEP 1. Your receiver should indicate it is receiving a signal. To tune your antenna, slowly move the antenna left, then right, until you find the position with the highest signal strength. It is important to turn the antenna slowly. Because the signal is digital, it takes a few seconds for the receiver to lock on. STEP 2. Place rotation clamp in the LOCK position. This prevents the antenna from moving and losing signal. STEP 3. Slowly raise, then lower the antenna until you have “peaked” the signal (found the strongest signal). ELEVATION TURNS CW 14 - 16o 14 17 - 19o 14-1/2 20 - 22o 15 23 - 25o 15-1/2 26 - 29o 16 30 - 32o 16-1/2 33 - 35o 17 3 o> - 3 CO o 17-1/2 39 - 42o 18 43 - 45o 18-1/2 46 - 48o 19 49 - 51o 19-1/2 52 - 54o 20 55 - 57o 20-1/2 58 - 61o 21 62 - 64o 21-1/2 65 -67° 22 68 - 70° 22-1/2 71-73° 23 WATCHING OFF-AIR TV To watch the area (local) television programming, use one of these options — • Use an A-B switch between the receiver and antenna power supply. • Use a video switch, Figure 1. • Connect antenna output from power supply to TV ANTENNA input on receiver, Figure 2. When you turn off the receiver, it automatically switches you to off-air. LOWERING ANTENNA TO TRAVEL POSITION STEP 1. Set rotation clamp to ROTATE position. STEP 2. Fully rotate antenna counterclockwise until pointer on directional handle aligns with red screw on rotation clamp. STEP 3. Turn elevating crank counterclockwise in direction of “DOWN” arrow until resistance is met. The number of turns will vary according to the elevation angle the antenna was set to. STEP 4. Move rotation clamp to the LOCK position. CAUTION: Under no circumstances lower the antenna to any position other than travel position!_ Rev. 11/11/03 OPERATIONS DO’S AND DON’T’S DO’S 1. Do check parking location for obstructions before raising antenna. 2. Do carefully raise, lower and rotate the antenna — if difficult, check for cause. 3. Do rotate slowly when searching for the satellite(s) and check fine tuning on TV set for pr...