Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• To lock the battery, push the battery lock mechanism to the right (1) until it locks into place (2). • To unlock the battery, push the battery lock mechanism to the left until it unlocks. ¦ Charge the battery Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous. This device is intended for use with the BL-5X battery. Always use original Nokia batteries. See "Nokia battery authentication guidelines" on page 81. G e t t i n g s t a r t e d Check the model number of any charger before use with this device. This device is intended for use when supplied with power from the ACP-12 charger. For availability of approved enhancements, please check with your dealer. 1. Connect the charger to a standard wall outlet. 2. Insert the charger plug into the round jack in the bottom of the phone. If the battery is completely empty, it may take a few minutes before the charging indicator appears on the display or before any calls can be made. 3. Disconnect the charger from the phone when the battery is fully charged. You can use the phone while the charger is connected. The charging time depends on the charger and the battery used. For example, charging a BL-5X battery with the ACP-12 charger takes approximately 1 hour and 5 minutes while the phone is in the standby mode. ¦ Turn the phone on and off Press and hold the power key as shown. If the phone asks for a PIN, enter the code, and select OK. When you turn on your phone for the first time, the phone is in standby mode (see "Standby mode" on page 15) and a query appears, asking for the configuration settings from your service provider (network service). Confirm or decline the query. See "Configuration settings service" on page 9. ¦ Open the keypad 1. Hold the phone in one hand. 2. With the other hand, press your thumb on the part of the phone that is below the display screen. 3. Push the top part of the phone (slide) upwards, as shown in the illustration. Getting started ¦ Normal operating position Use the phone only in its normal operating position. Your device has an internal antenna. Note: As with any other radio transmitting device, do not touch the antenna unnecessarily when the device is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed. Avoiding contact with the antenna area when operating the device optimizes the antenna performance and the battery life. Your phone 3. Your phone ¦ Keys and parts • Power key (1) • Loudspeaker (2) • Earpiece (3) • Left selection key (4) Right selection key (5) Middle selection key (6) The function of the selection key depends on the guiding text shown on the display above the key. • 4-way scroll key (7) that allows you to scroll up, down, left and right • Call key (8) dials a phone number and answers a call • End key (9) ends an active call and allows you to exit from any function • Battery cover release buttons (10) • Microphone (11) • Charger connector (12) • Enhancements connector (13) • Camera lens (14) • Headset HS-15, rotating clip (15) 15 Your phone ¦ Standby mode When you turn on your phone, the first screen that appears is the start screen, which indicates your phone is in the standby mode. When your phone is in the standby mode, the selection keys access specific functions, and the indicators appear on the start screen. Indicators show the status of the phone. • The name of the wireless service provider (1) displays in the middle of the start screen. • The signal strength indicator (2) shows the strength of the signal to your phone. The higher the bar, the stronger the signal. • The battery strength indicator (3) shows how much power is left in your phone battery. The higher the bar, the more power in the battery. • The left selection key (4) in the standby mode is Go to. Your most frequently used functions can be quickly accessed from the Go to menu. To activate a function, select it. To view a list with available functions, select Options > Select options. To add a function to the shortcut list, select Mark or to remove a function from the list, select Unmark. To rearrange the functions in your personal shortcut list, select Options > Organize. Scroll to the function you want, select Move, and scroll to where you want to move the function. • The middle selection key in the standby mode is Menu (5). • The right selection key in the standby mode may be Names (6) to access the Names menu, an operator-specific key to access an operator’s home page, or a specific function that you have selected in the right selection key menu. Power saving screen saver To save power, a digital clock screen saver overwrites the display when no function of the phone has been used for a certain period of time. Select Menu > Settings > Display > Power saver > On to activate the screen saver or press any key to de...