Login:
Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Anleitung Black Box, modell FX800AE

Hersteller: Black Box
Dateigröße: 116.8 kb
Dateiname:
Unterrichtssprache:enes
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


You can replace this antenna with an outdoor antenna for extended transmittion range. One of your local consumer electronics stores might carry an outdoor antenna. If you cannot locate a store that sells an antenna, call for technical support. • “Low Battery” alarm—shows when the pager’s battery level is low. 3.2 Tone Pager (FX801A) The Tone Pager beeps 12 times every ten seconds. This process is repeated three times and then the pager beeps once every 60 seconds. Pressing the on/off button allows you to view old messages from newest to oldest. Two FX801A pagers come with the FX800A; no pagers come with the FX810A (you must order them separately). UNPACKING THE FX801A The FX801A package includes: • (1) Tone Pager • This User’s Manual You can order additional pagers to work with your base unit. 13 CAMPUS PAGER 3.3 Vibrating/Tone Pager (FX802A) The Vibrating/Tone Pager works in a similar fashion, except that it does not beep 12 times every ten seconds. Instead, it vibrates once. The process does not repeat three times, but the unit does beep once every 60 seconds, and allows you to view old messages from newest to oldest by pushing the on/off button. The FX802A includes one pager; however, you can order additional pagers to work with your base unit. UNPACKING THE FX802A The FX802A package includes: • (1) Vibrating Pager • This User’s Manual You can order additional pagers to work with your base unit. For more information about how to properly install and operate the Campus Pager, read the rest of this manual. 14 CAMPUS PAGER 4. Installation 4.1 Positioning the Campus Pager You can operate the Campus Pager from a flat surface such as a table, counter, or shelf. Or, you can use the supplied wall-mount brackets to mount it on a wall. Steel and concrete walls reduce the Campus Pager’s transmitting range. If the Campus Pager is located in a concrete or steel building, and part of the coverage area is located outside the structure, place the unit and antenna close to a window. To mount the Campus Pager on a wall, follow these steps: 1. Slide the wall-mount brackets into the 2 wall-mount sockets, as shown in Figure 4-1. Figure 4-1. Connecting wall-mount brackets. 15 CAMPUS PAGER 2. Insert the center-loaded antenna connector into the antenna jack on the right side of the Campus Pager. Turn the connector clockwise until the antenna locks in place. For maximum efficiency, extend the antenna to its full length, orient it vertically, and keep it away from walls. See Figure 4-2. Figure 4-2. Connecting the antenna to the Campus Pager. 3. Mark the positions for the two supplied mounting screws on the wall. The positions should be 5-7/8” apart. Drill the two holes, then thread the two screws into the wall. The screws should extend 1/5”. Do not over-tighten the screws. 4. Align the keyholes on the back of the brackets with the two screws, then push in and press down to secure the Campus Pager to the wall. See Figure 4-3. 16 CAMPUS PAGER Figure 4-3. Connecting the C...

Dieses Handbuch ist für folgende Modelle:
Handys - FX800A (116.8 kb)
Handys - FX801A (116.8 kb)
Handys - FX802A (116.8 kb)
Handys - FX810A (116.8 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien