Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
ASSEMBLING YOUR BREVILLE DIE CAST CITRUS PRESS 9 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 10 Step 4. Step 5. Insert the Fruit Dome onto the underside of the Note: The Fruit Dome is keyed, and Place the Juicing Cone onto the Drive Shaft Juicing Press Arm by aligning the tab on top of can only be inserted in one way and press down lightly to lock the Cone the Fruit Dome with the hole in the Juicing Press into position. (this will ensure that it does not Arm. Hold onto the Juicing Press Arm and press rotate through operation). the Fruit Dome up and backwards until the Dome locks into position. 10 ASSEMBLING YOUR BREVILLE DIE CAST CITRUS PRESS 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 11 Step 6. Step 7. Ensure the Anti-drip Juice Spout is pushed down Place a suitable sized glass or jug underneath into the pouring position. the Juice Spout. ASSEMBLING YOUR BREVILLE DIE CAST CITRUS PRESS 11 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 12 Operating 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 13 OPERATINGYOURBREVILLEDIECASTCITRUSPRESS Step 1. Step 2. Step 3. Ensure the Die Cast Citrus Press is correctly Cut the citrus fruit in half by cutting across the Plug the power cord into a 120v power outlet assembled with a glass or jug, placed under the fruit segments, rather than across the tip ends, and then switch the On/Off button to ON. This Juice Spout before juicing commences. to ensure more efficient juicing. begins operation of the Citrus Press. For the best contact with the Fruit Dome, smooth the outside of the fruit by trimming any knobbly tip ends such as the ends of a lemon or tangelo. OPERATING YOUR BREVILLE DIE CAST CITRUS PRESS 13 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 14 Step 4. Place a citrus fruit half, cut side down, onto the Juice Cone. Step 5. Grasp the Soft Grip Handle and slowly lower the Juicing Press Arm and press down firmly until the Fruit Dome is in contact with the fruit skin. The motor will automatically start and the Juicing Cone will begin to rotate. The juice will be extracted from the fruit and flow through the Juice Spout into the glass. The pulp and seeds will collect in the Stainless Steel Filter. 14 OPERATING YOUR BREVILLE DIE CAST CITRUS PRESS TIP: Do not lower the Juicing Press Arm too quickly or the motor will hesitate and the Juicing Cone will not spin. This is because the Diecast Series Citrus Press is fitted with a motor that increases in strength as the motor spins. It is therefore better to push down lightly for the first few seconds to allow the motor to start spinning. The motor can then generate the strength necessary to cut through tough pulp. 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 15 Step 6. Step 7. The Die Cast Citrus Press juices very quickly so Remove the used fruit from the Juicing Cone. each fruit half will be juiced in a few seconds. To Empty excess pulp and seeds from Stainless automatically stop the motor, lift the Juicing Press Steel Filter as required. Arm up and backwards to its extended position. Repeat Steps 4-7 to continue juicing. NOTE: The Stainless Steel Filter should be emptied when full with pulp and seeds. The Filter can be emptied during juicing by switching the Citrus Press “OFF” at the On/Off button and carefully removing the Juicing Cone and Filter. Clean and replace Stainless Steel Filter and Juicing Cone before continuing to juice. Do not allow the Stainless Steel Filter to overfill as this may prevent correct operation or damage the unit. OPERATING YOUR BREVILLE DIE CAST CITRUS PRESS 15 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 16 DISASSEMBLINGYOURBREVILLEDIECASTCITRUSPRESS Step 1. Step 2.1 Step 3. Switch the Citrus Press “OFF” at the On/Off Pull the Juicing Press Arm up and backwards, Remove the Fruit Dome by pressing the button button and unplug the unit from the power away from the Motor Base, until fully extended. marked “PRESS” on the Juicing Press Arm. outlet. Step 2.2 Close the anti drip spout by pulling to upper position. 16 DISASSEMBLING YOUR BREVILLE DIE CAST CITRUS PRESS 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:23 AM Page 17 Step 4. Step 5. Lift the Juice Collector from the Motor Body with Follow recommended Care and Cleaning the Stainless Steel Filter and Juicing Cone still in guidelines and insert the Dust Cover before place. Remove the Cone and Filter from the Juice storing. Collector over a sink for easier cleaning. DISASSEMBLING YOUR BREVILLE DIE CAST CITRUS PRESS 17 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:24 AM Page 18 Cleaning 800CPXL_IB_V1.qxd:800CP Book 19/8/09 9:24 AM Page 19 CARE,CLEANINGANDSTORAGE • Always ensure that the Die Cast Citrus Press is switched OFF at the On/Off button and the plug is removed from the power outlet before cleaning, disassembling, assembling and storing the appliance. • Follow these instructions to clean all surfaces or parts that come into contact with food during juicing:- 1. For easy cleaning – immediately after each use rinse removable part...