Refer to back page for kit information. CHARGING-ON UNIT. If the battery has insufficient energy to crank the engine for starting, rope start the engine and allow it to run at medium to fast speed to restore charge. CHARGING-AUTO TYPE CHARGER: If the battery charge cannot be restored by running the engine, it may be too deeply discharged to accept charge. In this event, disconnect and remove the battery from the unit and charge on an automotive type charger at LOW RATE only (2 amp maximum) for

This two-stage Thrower will do a great job of clearing snow from your drives and walks on the rear engine Rider which not only provides weight on the rear drive wheels for excellent traction but gives you good forward visibility. This manual covers the recommended procedures for operating the unit as a snow thrower plus detailed instructions for converting the Rider to and from the mower mode as the seasons change. Before operating in the snow thrower mode, be sure to read the important safety i

U-shaped Bracket F. Ring Gear G. Nut Figure 21. Gear Bracket Adjustment A. Mounting Hardware B C Figure 22. Chute Rotator Motor Adjustment A. Screws G A E F D Gear Bracket Adjustment If the discharge chute becomes difficult to rotate or begins to operate erratically, the chute direction control rod gears may require adjustment: 1. Loosen the gear bracket mounting nuts (Figure 21). 2. Slide the gear bracket into the position that provides the best engagement between the gears. 3. Tighten the brac

NORTH AMERICAN MODEL DECALS CE MODEL DECALS 1727022 Part No. 1722867 Lubrication Decal (Tube Handle Models) 1727024 Part No. 1727024 - WARNING / Main Dash Decal, CE Channel Handle Models 1726946 Auger Disengage Auger Engage Part No. 1726946 Auger Control Decal Tube Handle Models 1727023 Part No. 1727023 Auger Control Decal Tube Handle Models Part No. 1722867 Lubrication Decal (Tube Handle Models) Safety Icons SAFETY ICONS WARNING: READ OPERATOR’S MANUAL. Read and understand the Operator’s Manual

10. Never direct the discharge toward people or areas where property damage can occur. Keep children and others away. 11. Do not overload the machine capacity by attempting to clear snow at too fast a rate. 12. Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse. 13. Disengage power to the collector/impeller when snowthrower is transported or not in use. 14. Use only attachments and accessories approved by the manufacturer o

Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug. PROBLEM POSSIBLE CAUSE REMEDY Engine fails to start. 1. Key is OFF. 1. Push key in to the ON position. 2. Failure to prime cold engine 2. Press primer button twice and restart. 3. Fuel valve is in CLOSED position. 3. Turn valve to OPEN position. 4. Out of fuel. 4. Fill fuel tank. 5. Choke OFF - cold engine. 5. Turn choke to ON, set throttle to FAST. 6. Engine flooded. 6. Turn choke to OF

5. To lower the height of the scraper bar, raise the skid shoes. 6. If the scraper bar becomes worn, it can be replaced by removing the hardware attaching it to the snowthrower. A B Figure 3. Chute Deflector Adjustment (Some Models) A. Chute Deflector Knob B. Chute Deflector Figure 5. Skid Shoe Adjustment A. Scraper Bar B. Skid Shoe C. Nuts Figure 4. Remote Deflector Control (Some Models) A. Maximum Throwing Position B. Spring C. Control Handle C A A B C B 13 Operation FULL TRACTION Easy Turn™ L

The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur. To avoid injury, keep others and yourself away from the auger and the discharge chute whenever the engine is running. Read and follow all of the safety rules and warnings in this manual. DANGER Do not clean out discharge chute with hands. Contact with moving parts inside chute will cause serious injury. Us

Lubricate Auger Shaft.*** 25 Hours 10 Hours Monthly 50 Hours. Yearly 4-6 Hours Yearly 10 Hours 10 Hours Winter Weight Worm Gear Oil 10W Oil and Grease 20 psi (1.37 bar) See Engine Manual See Engine Manual N/A Lithium Grease 10W Oil Lithium Grease MAINTENANCE REQUIRED FREQUENCY NOTES * Change original oil after two hours of operation. ** Check oil level each fall and spring. . See your engine Owner’s Manual. ***Lubricate each fall and spring. Pipe Plug Size PSI bar 15 x 5.0-6 20 1,38 4.80-8 20 1,

NOTE: Allow the engine to warm up at SLOW throttle for a few minutes before operating the snowthrower at full speed. The engine will not develop full power until it reaches operating temperature. After warming up, always operate at full throttle. 11 Operation OPERATING THE SNOWTHROWER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger engage control (C, Figure 2) on the right-hand grip to begin auger r