Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
If it becomes necessary to move across the face of a slope, use caution and do not blow snow. Be very careful when changing direction on a slope. Proper winter footwear is recommended for the operator to help prevent slipping. Never attempt to clean snow from excessively steep slopes. The maximum slope for any operation is 35 percent ( 19.3° ) which is a rise of 3-1 /2 feet vertically in 10 feet horizontally. A WARNING To avoid serious injury, do not put your hands into the auger housing or discharge spout. If auger stalls or spout plugs, use the following procedure to remove objects or clear the spout. 1. Release both drive levers. 2. Shut off the engine. 3. Wait for moving parts to stop. 4. Use a narrow board to remove foreign objects and clear the spout. Never put you hands into the auger or discharge spout, because tension buildup due to plugging could cause parts to rotate upon clearing. WARNING Before leaving the operator’s area for any reason, stop the engine and remove the key. Disconnect spark plug wire and secure away from plug to prevent accidental starting. ^WARNING When both levers are depressed, Free-Hand™ control is activated on auger control lever. Release lever on left-hand handle (traction lever) to stop auger and traction drive after Free-Hand™ control has been activated. 12 ENGINE SPEED Set the engine speed lever to full speed. Operation OPERATION 1. For operation on slopes, see the ’’Operation on Slopes“ warning box. 2. Start the engine. 3. Select desired ground speed and set engine speed to full. 4. To start snowthrower into motion, depress the Traction Drive Lever (figure 8). Releasing the lever will stop the forward or reverse motion of snowthrower. 5. The lever on right-hand side is the Auger control lever (figure 8). Depress this lever to engage the auger. Releasing the lever will stop the auger unless the the Free-Hand™ control has been activated. See step 6 for explanation of Free-Hand ™ control. 6. Depressing both levers activates the Free-Hand™ control. The operator can now release the Auger Control Lever, and the auger will continue to rotate. This allows the operator to rotate the chute without stopping the discharging of snow from the auger. When the Traction and Free-Hand™ contvol lever is released, both the auger and traction drive will stop. 7. Use of Free-Hand™ control will allow operator to rotate chute and adjust the deflector cap while snowthrowing. 13 Operation AFTER EACH USE A WARNING Never store the snowthrower in a building where gasoline fumes may reach an open flame, spark or pilot light such as on a furnace or water heater. 1. Before stopping engine, pull the starter rope twice and allow to rewind slowly. Then, stop the engine. This will help prevent freeze-up. 2. See the “To Stop Engine” section in your engine Owner’s Manual. It describes how to prevent engine free/e-up. 3. Always remove the key to prevent unauthorized use. 4. Clean snow and ice from the snowthrower. 5. If the snowthrower is kept in a cold shelter, fill the fuel tank to prevent condensation. Do not store near sparks or flame. 14 Normal Care NORMAL CARE CHART Care Required See Page Every 25 Hours Yearly Check auger gear case lubrication.** Page 17 • Lubricate snowthrower. Page 17 • Check tire pressure. Page 19 • Change engine oil.* Eng. Manual • Clean or replace spark plug. Eng. Manual • Check battery (if equipped). Battery Instructions • Check discharge control. Page 27 • ‘Change original engine oil after first two hours of operation. "Beginning and end of every season. Use Simplicity Worm Gear Oil only. See “Common Replacement Parts” page for specifications. Normal Care OFF-SEASON STORAGE Before you store your snowthrower for the off-season, take the following precautions: NOTE Fuel may be stored in the tank or in a container for long periods if a gasoline stabilizer is used. This additive, available from your dealer, prevents formations of gum and varnish for up to one year. 1. Prepare your snowthrower engine for storage according to your engine Owner’s Manual. 2. Lubricate the snowthrower as described in the Normal Care section. 3. If equipped with a battery, disconnect the cables or remove the battery from the snowthrower. The battery should be kept fully charged during storage. 4. Clean the snowthrower thoroughly. Coat all exposed bare metal parts with a good quality paint (available from your dealer) or a light film of grease, oil or automotive wax. 16 STARTING AFTER STORAGE 1. Remove the spark plug and wipe dry. Crank engine a few times to blow excess oil out of plug hole. Then reinstall plug. 2. Fill fuel tank with fresh gasoline (unless a fuel stabilizer was used). 3. Check to be sure engine fins are clean and air flow is unobstructed. 4. Check engine oil and lubricate snowthrower. 5. Start the engine outdoors. Do not run engine at high speeds immediately after starting. 6. Check the operation of the controls. If nece...