Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
16 x 1" 4 720002 7 Lock Washer, 3/S" 5 717003 7 Hex Nut, Full 3/8"-16 6 107106 2 Shoe Assy. 7 719001 4 Flat Washer, 3/S” 8 720002 4 Lock Washer, 3/8" 9 705004 4 Hex. Cap Screw, 174054 S/8'J-16 x 3/4" 10 1 Pivot Frame Assy. 11 715100 2 Hex Capscrew, l/2”-13 x 1-1/2" 12 717518 2 Hex Nut, 1/2"* 13 13 107116 1 Pivot Plate Assy. 14 722006 2 Cotter Pin 1/8“ x 1" 15 107118 1 Pivot Rod 16 722001 2 Cotter Pin, 3/32” x 3/4" 17 107119 1 Pivot Arm id 156150 1 Spacer 19 705007 1 Hex Capscrew, 5/16M-18x 1” 20 719002 1 Plain Washer, 5/16" 21 720001 1 Lock Washer, 5/16" 22 717001 1 Hex Nut, Full, 5/16”-18 23 107120 1 Pivot Stud 24 720001 1 Lock Washer, S/16" 25 717001 1 Hex Nut, Full, 5/16"-18 26 107121 2 Eyebolt 27 717001 4 Hex Nut, Full, 5/16-18 28 101126 2 Spring 29 1607913 1 Push Bar Assy. 30 174066 1 Pivot Pin Ref, No. P*rt No. Qty. Req. Description 31 722003 2 Cotter Pin, 3/16" x 1*1/4” 32 174073 1 Latch 33 723002 2 Roll Pin, 7/32" xl" 34 107135 1 Latch Spring 35 107136 1 Latch Rod 36 722001 2 Cotter Pin, 3/32" x 3/4" 37 118053 2 (Hitch) Pin 38 106788 2 Hairpin Clip 39 1608023 1 Front Lift Rod 40 8031007 2 Collar 41 713006 2 Set Screw S/16"-18x 1/2" 42 171011 1 Spring 43 171679 1 Rod Guide 44 106788 Hairpin Clip 45 106131 1 Fork Assy. 46 106788 1 Hairpin Clip 47 1607472 1 Rod Assy. 48 705018 1 Hex Capscrew, 5/16"-18 x M/2" 49 717511 1 Fuü Lock Hax Nut 5/16’'-18 50 1608075 1 Bracket 51 106687 1 Bracket 52 705004 1 Hex Capscrew, 3/8"-I6x3/4’' 53 720002 1 Lock Washer, 3/8" 54 717003 1 Hex Nut, Full 3/8M-16 55 172162 1 Eyebolt 56 7200CS 1 Lock Washer, 1/4” 57 717005 1 Hex Nut, FuU, 1/4-20 58 106719 1 Film, Simplicity 59 103005 1 Model No. Plate 60 172432 1 Fuel Tank Cap (Winterized) 61 177973 1 Transport Chain Assy. The 46" Snow plow and Dozer blade can be used without any weights or chains. HOWEVER, by using these items, plowing and dozing will be done more effectively and efficiently. Using the rear counter weight (Mfg. No. 182 with No. 045 will ease lifting of the front mounted attachments. This is mounted on the rear lift assy. Using wheel weights (1 or 2 on either side) will provide more traction. By adding chains with the wheel weights additional traction will be experienced. Loose mounting of the chains will assist in their self cleaning. OPERATION There are five operating positions for this blade. The position can be changed by the operator without leaving the seat. Turn the control rod clockwise to unlatch the blade. Push or pull rod to the desired position. For ease of changing positions, raise blade slightly from the ground. By adjusting the shoe assembly, various blade heights can be achieved. Increased height adjustment can be done by adjusting the slop pin in the lift lever quadrant. When the blade is used with the manual lift, the float cam can be placed in the float position so the blade will follow the contour of the ground without any downward pressure ?xcept the weight of the blade. The manual lift and the power lift can be used to lock the blade in any position desired. The spring on the lift arm allows the blade to lift over hard objects when downward pressure is maintained' on the blade. If it is desired to use a tiller or other attachment when the blade is mounted, the transport hook which is bolted to the frame at the front of the tractor should be used. With the blade hooked in the transport position, the lift arm can be removed from the tractor. The lift can then be used to raise or lower another attachment. LUBRICATION Lubricate all joints where rods enter holes. Also lubricate pivot points. Periodic lubrication will assist in ease of operation. PACKING The 46" Snow Plow and Dozer Blade comes in one carton with all necessary hardware. ASSEMBLY Attach hitch assembly to blade assembly, using the two yoke pins and cotter pins provided. Using the two eye bolts, attach spring from hitch to blade. Allow 1/2" of thread to show through nuts. Attach to tractor as indicated in Fig* 1 with the two pins and spring clips. Attach blade direction rod bracket at the frame hole on right hand side of the Fuel'Tank & Steering Post Support Assembly. See Fig. 1. (If this bracket has been installed for usage with another implement, it need not be removed). Attach lift rod to tractor lift lever and to plow. Fig. 1. Insert blade direction rod through bracket and attach to blade. Secure in place with spring clips. The wear plate on the blade is reversible. When one edge becomes worn, remove'the bolts, turn the blade around, and reinstall it so the unused edge is at the bottom. \ 1971 MODELS WHEEL WEJGHTS a | -CHAINS DIRECTION ROD BRACKET ATTACHES HERE ATTACH BLADE HITCH HERE FIGURE 1 Ref. No. Part No. Qty. Req. Description 1 705009 1 Hex Capscrew, 3/8"-16 x l-l/2,r 2 154177 1 Spacer 3 719001 1 Plain Washer, 3/8" 4 720002 1 Lock Washer, 3/8" 5 717003 1 Hex Nut, Full, 3/8"-L6 6 174438 1 Deflector 7 705002 2 ,.Hex Capscrew, 7 l/4T,...