Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Cub Cadet
Dateigröße: 4.58 mb
Dateiname: fc3d2da1-0748-8484-59fb-a314f3476d50.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Tire Pressure Adjustment The tires are over-inflated for shipping purposes. Check tire pressure and reduce to between 15 psi and 20 psi. NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other. Cable Guide “Z” End Auger Control Cable Jam Nut Skid Shoes Hex Nuts Traction Control and Shift Lever Adjustment To check the adjustment of the traction control and shift lever, proceed as follows: • Move the shift lever into sixth (6) position. a. With the traction control (refer to Figure 7 in Section 4 of this manual) released, gently push the snow thrower forward, then pull it back. Disregarding the overall weight of the snow thrower, the machine should otherwise move freely. b. Engage the traction control, and attempt to move them machine both forward and rearward. You should experience resistance as the wheels should not be turning. • Move the shift lever into the fast reverse (R2) position and repeat the previous steps (a & b). If you experienced resistance either when repositioning the shift lever from 6 to R2 or when attempting to move the machine forward or rearward with the traction control released, your snow thrower’s traction control is in need of adjustment and you should NOT operate the machine before completing the adjustment as follows: • Loosen the jam nut on the traction control cable and UNTHREAD the cable one full turn. • Recheck the adjustment. • Retighten the jam nut to secure the cable when correct adjustment is reached. If the machine can be moved freely both forward and rearward when the traction control fully depressed, proceed as follows: • Loosen the jam nut on the traction drive cable and THREAD the cable in one full turn. • Recheck the adjustment and repeat adjustment as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached. NOTE: If you are uncertain that you have reached the correct adjustment, refer to Traction Control Adjustment on page 10 of this manual. SECTION 4: KNOW YOUR SNOW THROWER Auger Control Chute Tilt Control Shift Lever Traction Control / Auger Control Lock Chute Directional Control Figure 7 Traction Control / Auger Control Lock The traction control is located on the right handle. Squeeze the traction control to engage the wheel drive. Release to stop. This same lever also locks the auger control so you can turn the chute directional control without interrupting the snow throwing process. If the auger control is engaged along with the traction control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release the traction control to stop both the augers and wheel drive (auger control must also be released). IMPORTANT: Always release tractional control before changing speeds. Headlight The headlight is on whenever the engine is running. Shift Lever The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel. It can be moved into any of eight positions. Forward Your snow thrower has six forward (F) speeds. Position number one (1) is the slowest. Position number six (6) is the fastest. Reverse Your snow thrower has two reverse (R) speeds. R1 is the slower, while R2 is the faster of the two. IMPORTANT: Always release tractional control before changing speeds. Auger Control The auger drive clutch is located on the left handle. Squeeze the clutch grip to engage the augers. Release to stop the snow throwing action. (Traction control must also be released.) 7 Chute Directional Control The chute directional control is located on left side of the snow thrower. To change the direction in which snow is thrown, turn chute directional control as follows: • Crank clockwise to discharge to the left. • Crank counterclockwise to discharge to the right. Chute Tilt Control The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Move the chute tilt control forward to decrease the distance, toward the rear to increase. Fuel Shut-off Valve The fuel shut-off valve, located under fuel tank, controls fuel flow from the tank. Always make certain it is in the Open (vertical) position Open Closed before attempting to start the engine. Throttle Control The throttle control is located on the engine. It regulates the speed of the engine. Primer Rope Starter Handle Choke Ignition Key Throttle Control Figure 8 Safety Ignition Key The safety ignition key must be fully inserted in the switch before the unit will start. Remove the ignition key when snow thrower is not in use. IMPORTANT: Do NOT attempt to turn the key. SECTION 5: OPERATING YOUR SNOW THROWER WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. Gas And Oil Fill-up • Check oil level and add oil if necessary. Service the engine with gasoline as instructed in the separate engine manual packed with your snow thrower. WARNING: Use extreme care when handlin...