Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Refer to Service and Adjustments section page 20 of this owner’s guide. YOUR RESPONSIBILITY • Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Following are representations of some of the safety labels on your Craftsman snowthrower. Please follow the instruction on these labels and maintain safety while using or servicing the equipment. A WARNING IA DANGER I AVOID INJURY FROM ROTATING AUGER -KEEP HANDS, FEET AND CLOTHING AWAY. A I A I I ' I DANGERI SHUT OFF ENGINE BEFORE UNCLOGGING DISCHARGE CHUTE. 1. STOP ENGINE BEFORE REMOVING DEBRIS AND SERVICING UNIT. 2. KEEP CLEAR OF IMPELLER WHILE ENGINE IS RUNNING 3. NEVER DIRECT DISCHARGE AT BYSTANDERS OR WINDOWS OR ALLOW ANYONE IN FRONT OF UNIT 4. THOROUGHLY INSPECT THE AREA THE EQUIPMENT IS TO BE USED AND REMOVE ALL DOOR MATS, SLEDS, BOARDS, WIRES AND OTHER FOREIGN OBJECTS 5. REFER TO OWNERS MANUAL FOR FULL INSTRUCTIONS „7» 4 ACCESSORIES These accessories were available when the snow thrower was purchased. They are also available at most Sears retail outlets, catalog and service centers. Most Sears stores can order repair parts for you when you provide the model number of your snow thrower. Belt Gasoline Can Spark Plug 5 HARDWARE PACK Lay the hardware pieces from the hardware pack on the figure here and you will have automatically sorted these according to the steps of the assembly procedure described later. (Only one unit of each hardware has been shown per group. The number in parenthesis indicates the total number of the hardware needed in that group.) 6 ASSEMBLY Traction Drive Control Chute Figure 1 IMPORTANT: This unit is shipped with engine oil, but without gasoline, in the engine. After assembly, see OPERATION section of this manual for fuel selection and fill-up. NOTE: To determine right and left hand sides of your snow thrower, stand behind the unit with the engine farthest away from you. See Figure 1 inset. Your snow thrower has been completely assembled at the factory, except the handle and the handle panel, the discharge chute assembly, the chute crank assembly and the shift rod. These parts are shipped loose in the carton. Removing From Carton • Cut the corners of the carton and lay the sides flat on the ground. Remove all packing inserts. • Remove all loose parts. For a complete list of the loose parts, refer to the following section. • Move the snow thrower out of the carton. • Make certain all parts and literature have been removed before discarding the carton. Loose Parts (See Figure 1.) a. Handle Panel and Chute Assembly b. Right Hand Handle c. Left Hand Handle d. Chute Crank Assembly e. Shift Rod f. Hardware Pack Assembly Tips: For easier assembly purposes, remove the chute from the carton and lay it on top of the engine. Do not unwrap the chute till you have installed the handle panel and the clutch cables. Tools Required 1. 1/2", 7/16”, 3/8” wrenches or a set of adjustable wrenches 2. Set of standard head screw drivers 3. Set of philips head screw drivers 4. Funnel ák WARNING: Make certain the spark plug wire is disconnected and moved away from the spark plug before assembling the snow thrower. Attaching Handle Assembly • Stretch out control cables and place on the floor. Place the right handle in position with the flat side against the snow thrower. You can identify the right handle by the traction drive control label on it and the left handle by the auger dutch control label on it. • Secure bottom hole in the handle to the snow ASSEMBLY thrower using 5/16 x3/4" hex bolt and lock washer from the hardware pack (group A on page 6). Do not tighten at this time. See Figure 2. Lock Washer & • Place a handle tab, included in the hardware pack (group A on Page 6), over the upper hole in handle so that the contour of the handle tab matches that of the handle. See Figure 2. • Secure handle tab to the snow thrower using hex bolt (5/16 x 1 -3/4" long) and lock washer from the same group in the hardware pack. Do not tighten at this time. • Attach the left handle in the same manner. Do not tighten at this time. • Place the handle panel in position between the handles so the ends of the curved part of the handles go through the slots in the handle panel. Align the holes in the handle with the holes on the two sides of the handle panel. See Figure 3. Right Handle Figure 3 • Attach the handle panel to the handle with two carriage bolts, cupped washers (cupped side against the handle panel) and hex nuts on each side. See Figure 3. You will find these fasteners in the hardware pack (group B on page 6). Align the contour of the carriage bolt head with the handle. • Attach each side of rear of handle panel with one 1 /4-20 hex bolt and flange nut from the hardware pack (group C on page 6). See Figure 3. Do not tighten at this time. • Tighten all loose hardware on the handle assembly in the followin...