Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Pivots blade to the right and left. ANGLE LOCK BARS Locks the blade in either the right hand, left hand or straight ahead position. BLADE ADJUST SPRING Holds blade in position but permits it to pivot forward to pass over an obstruction. BLADE SHOE Ground-contacting part of blade. Adjusts for adequate ground clearance of blade. BLADE PIVOT SHAFT Connects blade to channel assembly. Mows blade to pivot forward. MFT HANDLE ROD Connects lift handle tube to channel assembly. Raises and !owers the blade. CONTROL CABLE Connects the lock release lever to the angle lock bars. HOW TO USE YOUR SNOW BLADE To Pivot the Blade Raise the blade to transport position. To unlock To Raise or Lower the Snow Blade the blade, push the lock release grip down against , Use the handle grip located on the end of the handle the handle tube. To pivot the blade, keep the grip tube. To raise the blade, pull back while pushing down depressed and push forward or put! back on the on the handle grip= To lower blade, pul! back while handle tube, sliding it along the lift rod. Release the lifting up on handle grip. grip to lock the blade when it is in either the right hand, the left hand or the straight ahead position. PULLBACK AND LiFT UP TO LOWER BLADE LOCK RELEASE GRmPASSEMBLY HANDLETUBE \ ,I PULL BACK AND PUSH DOWN TO RAISE BLADE FIGURE 23 FIGURE 24 11 Wheelweightsandtire chainsmustbeusedwith yoursnowbladefor traction.These accessories are available at your nearest Sears retail store. Using the Snow blade , Prepare the lawn tractor engine for cold weather using instructions furnished with the lawn tractor, Always begin with the transmission in first (low) gear and gradually increase speed as required, Do not repeatedly push snow in the same direction, This causes excessive build up with each successive pass, To reduce icing on the blade, allow the lawn tractor and blade to adjust to outdoor temperature before operating, For improved snow removal performance, coat the blade with automotive type paste wax, CAUTION: Carefully inspect the area to be worked before operating the snow blade, Avoid pipes, roots, curbs or other heavy obstructions, CAUTION: Know the terrain, Avoid exceptionally steep slopes or drop-offs which may be hidden by the snow, Never run the snow blade into heavy material at high speed, CAUTION: Always lower the blade to the ground before leaving the tractor, CUSTOMER RESPONSiBiLiTiES Read and follow the maintenance schedule and the procedures listed in the maintenance section, MAINTENANCE SCHEDULE Fill in dates as you Service Dates complete regular service. Check for loose fasteners Check for worn or damaged parts Clean Blade x x Lubricate BIade x CHECK FOR LOOSE FASTENERS During the operating season, check all bolts, nuts and hairpin cotters to be sure they are secure, GREASE CHECK FOR WORN OR DAMAGED PARTS , During the operating season, check for worn and damaged parts, Replace or repair any that have excessive damage or wear, CLEAN BLADE ,, During the operating season, clean the blade off after each use, Touch up any bare metal with paint or apply a light coat of grease or rust preventive, LUBRICATE LUBRICATE BLADE , Lubricate al! pivot points to help maintain proper operation of blade, Use grease packet furnished with FIGURE 25 the snow blade for lubrication of the upper portion of the lift handle rod, 12 To Adjust Blade Spring , The tension of the blade adjust spring may be altered to permit the blade to tilt forward to bypass solid obstructions. To change the spring tension, adjust the nuts at upper end of the spring bolt. Standing in front of blade, turn the nuts counterclockwise to relieve tension and clockwise to increase tension. Refer to figure 17 on page 9. TO Adjust Blade Shoes , The blade shoes at the ends of blade may be raised for close work on smooth surfaces or lowered to raise the blade to work on rough or uneven areas. Make sure both shoes are set evenly and that the nuts are tightened securely. \ BLADE SHOE FIGURE 26 To Adjust the Blade Pivot Lock Mechanism if the blade wil! not unlock and pivot, the angle lock bars are not disengaging from the slots in the pivot plate. To correct, adjust the 5/16" hex jam nuts to draw the end of the control cable back towards the cable mount bracket=The less the threaded end of the cable extends through the bracket, the more the angle lock bars can retract to disengage from the slots in the pivot plate. CABLE MOUNT BRACKET t CONTROL CABLE 5/16" HEX 5/16" HEX JAM NUT JAM NUT FIGURE 27 Recommendations When Storing Remove the hairpin cotter which fastens the lift handle , When the snow blade is not being used, remove all rod to the lift link pin. See figure 19, page 10. dirt and rust and touch up with paint. Remove the hairpin cotter from the channel pivot pin , Touch up bare metal with paint or apply a light coat of and remove the pivot pin from the channel assembly. grease or rust preventive. See figure 18 on page 9. Lubricate all pivot points and all points shown in fig...