Stimmen - 4, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: MTD Dateigröße: 919.05 kb Dateiname: Unterrichtssprache:

Hold the blower drive belt up as the units are tipped together. Be sure the blower brake shoe seats on the blower sheave. Secure with the two cap screws into the frame. 2. Roll the blower belt on to the engine sheave. Pull the recoil starter rope to turn the engine sheave and roll the belt into place under the belt finger. 3. Check the belt finger spacing. There should be 1/8 inch clearance between the belt finger and belt with the blower clutch engaged. Readjust the belt finger if required. 4. Check the sheave alignment with the blower belt in place. Readjust as required to align the sheaves. It may be necessary to tip the blower housing away from the tractor to gain access to the blower sheave. 5. Replace the belt guard and chute crank assemblies. Readjust the chute crank as described in the paragraph above. Replace the spark plug wire. REPLACEMENT OF FRICTION WHEEL 1. Tip the machine up on the blower housing and brace securely. Remove two cap screws at back of frame securing the bottom cover and loosen two cap screws at front frame sides and remove the cover. 2. Remove the four whizlock nuts holding the bearing flange on the right hand side of the frame. Remove the bearing flange and carriage bolts. 3. Remove the hairpin cotter from the traction clutch rod. Pull this rod from the clutch fork arm and tip it up and out of the way. 4. Slide the friction wheel assembly and hex shaft to the right until the left end of the hex shaft comes free of the left bearing. Then slip the whole assembly back to the left and pull it forward out of the frame. 5. With the friction wheel assembly out of the frame, the three cap screws holding the friction wheel to the hub may be removed and the friction wheel removed. 6. Position a new friction wheel on the hub and secure with the three cap screws. Tighten securely. 7. Slip the right end of the complete friction wheel assembly and hex shaft into the hole in the right side of the frame. Position the friction wheel hub in the forks. Be sure washers are in place on bearing flange pins. Slide the hex shaft to the left and into the left bearing being sure flat washer is in position. See that the pinion gear meshes with the large gear. 8. Replace the bearing flange on the right side of the frame and secure with the four carriage bolts and nuts. Reconnect the traction clutch rod in the clutch fork arm and secure with a hair pin cotter. Readjust the traction clutch as described above. FLATWASHE (OUTSIDE OF (jk. PINION) 1/8 • 3/16' TRACTION clutch rod; FIGURE 6 LUBRICATION ENGINE Fill crankcase with Ariens Sno-Thro oil 5W-20 when using Sno-Thro. Use Ariens Gard-N-Yard oil MS classification SAE-30 when using lawn attachments. Refer to engine owners manual for appropriate crankcase oil substitutes. Fill fuel tank with fresh, clean unleaded automotive gasoline. (Leaded "regular" grade gasoline is an acceptable substitute.) NOTE: For detailed instructions on engine refer to manufacturer's booklet packed with the machine. TRACTOR DRIVE At the start* of season, grease hex shaft as indicated in Figure 7. Use Ariens Moly Lithium grease. Put two or three drops of light oil on shift lever and other linkage points. CAUTION: Do not allow grease or oil to come in contact with friction wheel, drive disc or belts. FIGURE 7 SNO-THRO UNIT The blower gear case is lubricated with Ariens Liquid Grease (Part No. 000070). This grease will not flow at lower temperatures. It is therefore difficult to check the lubricant level. Best method for checking is to place the unit in a warm location overnight. This allows the grease to flow to level. Check the lubrication by removing the filler plug on the side of the gear case just above the left auger shaft. Lubrication should be even with the hole with the machine sitting level. It may be necessary to insert a wire into the hole to check level. The unit will not be damaged by over lubricating. SHEAR BOLT« SHAFT FILLER PLUG FIGURE 8 Oil rake shaft periodically or each time a shear bolt is replaced. At the end of the season, remove shear bolts, oil rake shaft through shear bolt holes, turn rakes on shaft several times and replace shear bolts. Oil the discharge chute with several drops of heavy oil. STORAGE ENGINE — Follow detail instructions in the Engine Manual. SNO-THRO — Lubricate, clean and repaint as necessary. Cover and store in dry place. -7- TRACTOR PARTS FOR MODEL 932001, 932004, 932006 & 932007 PIECES DU TRACTEUR DES MODELE 932001, 932004, 932006 &932007 8- TRACTOR PARTS FOR MODEL 932001, 932004, 932006 & 932007 PIECES DU TRACTEUR DES MODELE 932001, 932004, 932006 &932007 Node NO DECODE REF. PlECi D'INV REF. PART STOCK DESCRIPTION NO. NO. CODE 932001 I QUANTITÉ NO. REQ’D « Ш ООО ООО CM CM CM СО n CO NoDE No DE REF. PIECÉ REF. PART NO. NO. CODE D’INV. STOCK DESCRIPTION CODE 932001 1 QUANTITÉ NO. REQ’D ^ r- I ss см ем CM со CO CO 05 0> 05 1 032070 FRAME 1 1 1 69 063003 LOCKWASHER 2 2 2 2 032002 SHIFT F...

Herunterladen

Geben Sie zwei Ziffern: