Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This washer has an i/2’ O.D. and a hole in the middle slightly smaller than i/16” I.D. 1. Remove the upper left-hand panel from the tractor to expose the valve (A, figure 1). 2. Notice there are two elbows on the side. Disconnect the hose (B) from the front elbow (C). Remove the elbow. 3. Place the washer so it is fully seated inthe hole. 4: Reinstall the elbow (C) and then connect the hose (B). Tighten the nut securely after elbow is properly positioned. Note: Flow reduction washer can be left installed in hydraulic valve for use with mower and other attachments. Chute Rotator Bracket Install the chute rotator bracket (A, figure 2) as follows: 1. Remove top front capscrew (B), lo&washer, and nut from the tractor. Retain hardware for reassembly. 2. Remove the bottom bolt (C) and discard. Retain the flange nut for reassembly. 3. Insert the bracket (A) between the tractor frame and footrest. Secure with existing hardware in the top front location, At the bottom hole, install 3/8-16x i-1/2” capscrew and flat washer from outside the frame, with a second flat washer placed between the rotator bracket and footrest bracket. Capscrew and flat washers are supplied in kit hardware bag. Secure with the existing flange nut. 4. Tighten all hardware. Figure 1. Flow Reduction Washer A. Valve 8. Hose C. Front Elbow Chute Rotator Bracket Top Capscrew C. Bottom Capscrew 6 Lift Rod 1. Lay lift rod (A, figure 3) next to the tractor so that rear clevis (B) with square weldment (C) is towards the rear. The weldment is positioned to prevent clevis pin (D) from being installed from the right hand side (interference would occur). 2. The lift rod must be inserted from the rear of the front axle, aligning rear clews (B) with the tractor lift lever (F). Install clews pin (D) from inside and secure and spring clip (E). Figure 3. Installing Lift Rod A. Lift Rod D. Clevis Pin B. Rear Clews E. Spring Clip C. Square Weldment F. Tractor Lift Lever Install Discharge Chute 1. Install nylon ring (A, figure 4) over snowthrower bottom discharge opening. 2. Install chute underneath left rear retaining bracket (B, factory installed). Make sure that chute ring gear teeth mesh with spiral rotator spring. The PTO retaining hook(F) should be pre-installed in the outside hole of the left rear bracket, if not, install it using l/4-20” nut. 3. Install three other chute retaining brackets (B) and secure with 1/4-20x 3/4” capscrews (C), lo&washers (D) and i/4-20 nuts (E). 4. Tighten hardware securely with two 7/16” wrenches. Figure 4. Installing Spout A. Nylon Ring 8. Chute Retaining Bracket C. Capscrew D. Lockwasher E. Nut F. PTO Retaining Hook 7 Mounting Hitch 1. Park tractor on a hard level surface. 2. Stop engine, lock parking brake, and remove key. 3. Place hitch on ground in front of tractor with pivot plate facing away from tractor. 4. Rotate the hitch attaching links rearward toward the tractor. 5. Install the back of hitch so that hitch pins (A, figure 5) are cradled in tractor hitch bracket (B). The lift rod front clevis must be positioned over the hitch lift arm while raising hitch into position. 6. From inside hitch, install the left and right clevis pins (C)through attaching links and tractor hitch bracket (B). Secure with spring clips (D). 7. Align the holes in the lift rod front clevis and tractor lift arm (may have to lift up on front hitch slightly). To avoid interference, install the clevis pin (E) from inside (flat head towards PTO belts). Secure the clevis pin with spring clip on outside of lift arm clevis. 8. Check the “Transport Height Adjustment” procedure on page 11 before snowthrower is installed. Install PTO Driveshafl 1. Install l/4” x 1” square key in keyway. 2. Install driveshaft (A, figure 6) with setscrew over key. 3. Secure the driveshaft with l/4-20 x 1 7/8”capscrew (Grade 5) and i/4-20 locknut at location B. NOTE: 1/4-20x l-7/8 capscrew supplied in kit hard ware bag has been ground to exact/y l-7/8 length for use in this step. 4. Rotate the PTO driveshaft and check clearance with the flat bearing boss just underneath. Peen end of capscrew to prevent locknut from backing off. 5. Tighten the setscrew over key with 3/16” allen wrench. 6. Release the PTO support rod (C) from retaining hook (D) and support driveshaft with rod. Figure 5. Mounting Hitch A. Hitch Pins B. Tractor Hitch Bracket C. Clevis Pin D. Spring Clip (Hitch) E. Clevis Pin Figure 6. Installing PTO Drvieshaft (Snowthrower Side) A. Driveshaft B. Capscrew Location C. PTO Support Rod D. Retaining Hook (Note: Hydraulic chute rotator model shown in photo.) 8 Mounting Snowthrower Note: The auger blades are shipped in identical position for shipping purposes. Remove either left or right hand shear bolt (refer to figure 18 on page 14) then turn one auger 180” and reinstall shear bolt. 1. Park tractor on hard level surface. 2. Stop engine, lock parking brake and remove key. 3. Place snowthrower’s shot pins (A, figure 7) in released position (shot pins shown in figure 7 a...
Dieses Handbuch ist für folgende Modelle:Schneefräsen - 1692244 (269.81 kb)