Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
5. Stop the engine (motor) whenever you leave the operating position, before unclogging the auger housing or discharge chute, and when making any repairs, adjustments or inspections. 6. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the auger blades and all moving parts have stopped. Remove key. 7. Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous. 8. Exercise extreme caution when operating on slopes. 9. Never operate the snow thrower without proper guards, and other safety protective devices in place and working. 10. Never direct the discharge toward people or areas where property damage can occur. Keep children and others away. 11. Do not overload the machine capacity by attempting to clear snow at too fast a rate. 12. Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse. 13. Disengage power to the auger blades when snow thrower is transported or not in use. 14. Use only attachments and accessories approved by the manufacturer of the snow thrower. 15. Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. 16. Never touch a hot engine or muffler. Clearing a Clogged Discharge Chute Hand contact with the rotating auger blades inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. To clear the chute: 1. SHUT THE ENGINE OFF! 2. Wait 10 seconds to be sure the auger blades have stopped rotating. 3. Always use a clearing tool at least 15 inches long. Maintenance and Storage 1. Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition. 2. Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure. 3. Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period. 4. Maintain or replace safety and instruction labels, as necessary. 5. Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller. TABLE OF CONTENTS SAFETY RULES ........................................................2-3 MAINTENANCE .....................................................11-15 PRODUCT SPECIFICATIONS ...................................... 3 STORAGE ................................................................... 16 CUSTOMER RESPONSIBILITIES ................................ 3 TROUBLESHOOTING ................................................ 17 SAFETY AND INSTRUCTIONAL DECALS ................. 4 REPAIR PARTS ..................................................... 18-26 SETUP........................................................................ 5-6 WARRANTY ................................................................ 28 OPERATION ............................................................ 7-11 KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. IMPORTANT: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. .. ..........2 ..........% ..........% ........% ..........2 ......, ...., ..................' ... ....& ........................................................................... ...................................................................................... ........................................................................................ .......................................................................................................... 4 5 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1. No parts required – Unfold the handle. 2. Carriage bolts Flange nuts Washers Knob Chute Deflector 5 4 2 1 1 1 Install the discharge chute. Install the discharge chute. Install the discharge chute. Install the discharge chute. 1. Unfolding the Handle Procedure 1. Loosen the two handle knobs and pull out the two handle bolts until you can move the handle freely and rotate the handle to the operating position (Figure 2). 2. Tighten the handle knobs until they are snug (Figure 3). 2. Installing the Discharge Chute 5 Carriage bolts 4 Flange nuts 2 Washers 1 Knob 1 Chute 1 Deflector Procedure Install the discharge chute as shown (Figure 4). ...
Dieses Handbuch ist für folgende Modelle:Schneefräsen - 96182000500 (6.93 mb)