|
Anleitung Zusammenfassung
A clean work area at the start of each job will allow you to perform service repairs easily and quickly. To reduce the incidence of misplaced tools or parts, place removed components with all attaching hardware in the disassembly order on a clean work surface. Organization is a key part of proper reassembly. Tools, instruments, and parts needed for the job should be gathered before work is started. Interrupting a job to locate tools or parts is a needless delay. A list of required special tools has been included in this manual. 2.7 SERVICE POSITION WARNING: ALWAYS block wheels and know that jack stands or blocks used are stable, strong, or secure and will hold the weight of the unit during maintenance. To ensure the unit is positioned in the proper service position place unit on a flat level surface. ALWAYS stop engine. Assure unit is secure and will not tip over. Strap and clamp onto lift if used. For additional requirements see section on service position. 2.8 CLEANING AND STORAGE WARNING: AVOID SHARP EDGES which can cut. Movement of parts can cut off fingers or a hand. Wear gloves, and use extreme caution when servicing. IMPORTANT: Never spray unit with water or store unit outdoors to help prevent sealed bearing rust or corrosion. Water can seep into sealed bearings and reduce component life. Bearings are sealed against dirt and debris only. A unit that is excessively dirty should be cleaned before work starts. Cleaning will occasionally uncover trouble sources. Dirt and abrasive dust reduce the efficient work life of parts and can lead to costly replacement. When taking unit out of extended storage: 1. Check for any damage or loose parts. Repair, replace, or tighten hardware before operation. 2. If a preservative fluid was used in fuel tank, drain and discard. Fill fuel tank with fresh new fuel. 2 - 4 2.9 SAFETY RULES Walk Around Inspection Complete a walk around inspection of unit and work area to understand: • Work area. • Your unit. • All safety decals. Work Area ALWAYS check overhead and side clearances carefully before operation. ALWAYS be aware of traffic when operating along streets or curbs. ALWAYS keep hands and feet within the limits of the unit. Keep children, people, and animals away. Keep children out of work area and under watchful care of a responsible adult. Keep area of operation clear of all toys, pets, and debris. Stay alert for hidden hazards. DO NOT run engine in an enclosed area. Always provide good ventilation. Unit ALWAYS keep protective structures, guards, and panels in good repair, in place and securely fastened. NEVER modify or remove safety devices. Operation Understand: • How to operate all controls • The functions of all controls • How to STOP in an Emergency • Speed ranges Before starting engine, disengage auxiliary power. Always back up slowly. Always look down and behind before and while backing. Never leave a running unit unattended. ALWAYS shut off auxiliary power, lower throttle setting, and stop engine before leaving unit. ALWAYS remove key to prevent unauthorized use. ALWAYS operate unit in good visibility and light. Fuel is highly flammable and its vapors can explode. Use ONLY approved RED fuel containers. NO Smoking! NO Sparks! NO Flames! Allow engine to cool before servicing. NEVER fill fuel tank when engine is running, hot, or unit is indoors. Abnormal Vibrations are a warning of trouble. Striking a foreign object can damage unit. Stop unit and engine. Wait for all moving parts to stop. Remove wire from spark plug. Inspect unit and make any necessary repairs before restart. Hazardous Slopes DO NOT operate on steep slopes. Avoid operating on slopes. When you must operate on a slope, travel up and down the slope. Never operate cross a slope. Never operate on a slope greater than 10 degrees. Child Safety NEVER allow children to operate or play on or near unit. Be alert and shut off unit if children enter area. Personal Safety Read and obey all warning, caution, and instructions on the unit and in provided manuals. • Only trained adults may operate unit. • Training includes actual operation. • Clearly understand instructions. • Be alert! Conditions can change. NEVER operate unit after or during the use of medication, drugs or alcohol. Safe operation requires your complete and unimpaired attention at all times. NEVER allow anyone to operate the unit when their alertness or coordination is impaired. DO NOT operate unit without wearing adequate outer garments. Wear adequate safety gear and protective gloves. Wear prop...
Dieses Handbuch ist für folgende Modelle:Schneefräsen - 924 SNO-THRO 924108 (764.68 kb)
Schneefräsen - 924 SNO-THRO 924110 (764.68 kb)
Schneefräsen - 924 SNO-THRO 924112 (764.68 kb)
Schneefräsen - 924 SNO-THRO 924113 (764.68 kb)