Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Honda Power Equipment Dateigröße: 4.14 mb Dateiname: Unterrichtssprache:

Adjust your snowblower ground speed (not engine speed) and snowblowing swath accordingly. Check the skid shoes for proper adjustment. Adjust the skid shoes to obtain the auger ground clearance for the type of surface the snowblower will be operated over (page 51 ). OPERATION OPERATION Before operating the snowblower for the first time, please review both the SNOWBLOWERSAFETYchapter (page 5 ) and the BEFORE OPERATIONchapter (page 18 ). Even if you have operated other snowblowers, take time to become familiar with how this snowblower works, and practice in a safe area until you build up your skills. Never tamper with, or alter any of the controls or safety devices on the snowblower. For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your snowblower’s exhaust contains poisonous carbon monoxide gas that can collect rapidly in an enclosed area and cause illness or death. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. STARTING THE ENGINE 1. Move the shift lever to ‘‘N’’ (Neutral) position. N (Neutral) SHIFT LEVER DRAIN KNOB FUEL VALVE ON DRAIN KNOB FUEL VALVE ON N 2. Set the transmission release ENGAGED lever in the ENGAGED position (page 16 ). TRANSMISSION RELEASE LEVER 3. Turn the fuel valve to the ON position. Be sure that the drain knob is tightened securely. 4. In cold weather and when the THROTTLE LEVER engine is cold, follow the procedures below. HS724/HS928: Move the throttle lever to the CHOKE position. CHOKE OPERATION HS1132: Pull the choke knob to the CLOSED position and move the throttle lever to the FAST position. CHOKE KNOB CLOSED FAST THROTTLE LEVER 5. Start the engine. Electric-start Models (TAS, WAS type): a. Connect your power cord to the switch box and the male end of the power cord to a properly grounded 120 Volt ac outlet. POWER CORD To minimize the possibility of potentially dangerous electrical shocks, always use a 3-conductor power cord with a power rating of no less than 15 amps. Also, be sure that the outlet you are using is properly grounded. Do not connect and disconnect the power cord with wet hands. Be sure to hold the plug when disconnecting the power cord from the electrical outlet or switch box. Do not disconnect by pulling on the power cord. OPERATION b.Turn the engine switch to the ON position. ON ENGINE SWITCH c. Push the starter button until the engine starts. After the engine PUSH starts, disconnect the power cord from the electrical outlet, and then from the switch box. Donotoperatethestarterformorethan1minute.Iftheengine failstostart,releasethebuttonandallowthestartertocoolfor15 minutesbeforeoperatingitagain. Manual Starting only a. Turn the engine switch to the ON position. b.Pull the starter grip lightly until you feel resistance, then pull briskly in the direction of the arrow as shown. c. Return the starter grip gently to the engine. STARTER GRIP DDiirreeccttiioonn ttoo ppull Donotallowthestartergriptosnapbackagainsttheengine.Return itgentlytopreventdamagetothestarter. Donotpullthestartergripwhiletheengineisrunning.Thestarter couldbedamaged. OPERATION 3. Let the engine warm up for several minutes. HS724/HS928: If the throttle lever has been moved to the CHOKE position, gradually move the throttle lever to the SLOW position as the engine warms up. THROTTLE LEVER SLOW HS1132: If the choke knob has been pulled to the CLOSED position to start the engine, gradually push it to the OPEN position as the engine warms up. Move the throttle lever to the SLOW position. SLOW OPEN CHOKE KNOB THROTTLE LEVER OPERATION 4. While warming the engine up, also warm the transmission as follows: a. Check that the shift lever is in the ‘‘N’’ (Neutral) position. SHIFT LEVER N (Neutral) DRIVE CLUTCH LEVER b.Squeeze the drive clutch lever for about 30 seconds to warm up the transmission fluid. STOPPING THE ENGINE To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following procedure. OFF ENGINE SWITCH OPERATION 1. Release the auger and drive clutch levers. The drive and snow blowing mechanism will stop operation. AUGER CLUTCH LEVER DRIVE CLUTCH LEVER 2. Move the shift lever to ‘‘N’’ (Neutral) position. SHIFT LEVER N (Neutral) 3. Turn the throttle lever to the SLOW position. HS724/HS928: HS1132: THROTTLE LEVER THROTTLE LEVER SLOW SLOW OPERATION 4. Turn the engine switch to the OFF position. ENGINE SWITCH OFF 5. Turn the fuel valve to the OFF position. OFF FUEL VALVE OPERATION CLEARING SNOW 1. Move the throttle lever to the FAST position for normal operation. R (Reverse) N (Neutral) 2. Release the auger clutch lever, and move the shift lever to select the desired drive speed. FAST F (Forward) Low speed is recommended for removing deep or hard-packed SHIFT LEVER snow. 3. Set the foot pedal to the correct position (page 14 , track type only). 4. Adjust the throwing direction by...

Herunterladen

Geben Sie zwei Ziffern: