Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Country Home Products, modell A2130BEA

Hersteller: Country Home Products
Dateigröße: 429.64 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

7. Do not attempt to operate on steep slopes or near embankments. 8. Use extra caution when backing up. 9. Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protection such as earmuffs or earplugs to protect your valuable hearing. 10. Always wear eye protection during operation (safety goggles, face shield, etc.). 11. Never allow anyone to operate the equipment until they read the manual completely and are thoroughly familiar with basic DR® ALL-TERRAIN™ MOWER and equipment operation. 12. Always make sure all equipment components are properly installed and securely fastened BEFORE operating. 13. Adjust collector-housing height to clear gravel or crushed rock surface. 14. If the DR® SNOW THROWER starts to vibrate abnormally, stop the engine immediately, disconnect the spark plug wire and check for cause. Excessive vibration is generally a sign of trouble. 15. Never operate the DR® SNOW THROWER without guards and other safety protective devices in place. 16. Do not direct the discharge chute at bystanders or animals. Ejected objects may cause injury. Read the separate DR® ALL-TERRAIN™ MOWER Operator's Manual carefully before using the machine. Lack of operating knowledge can lead to accidents. DR® SNOW THROWER Safety, Operation & Maintenance Instructions SAFETY PRECAUTIONS Maintenance ALWAYS USE GENUINE PARTS WHEN REPLACEMENT PARTS ARE REQUIRED ! WARNING: Always disconnect the spark plug wire before servicing your machine. 1. Park the DR® ALL-TERRAIN™ MOWER on level ground, set the parking brake, disengage the driving system, place all levers including auxiliary control levers in neutral, shut off the engine and remove the spark plug wire BEFORE making any adjustments. 2. Make sure all shields and guards are securely in place following all service, cleaning, or repair work. 3. To avoid injury, do not adjust, unclog or service the equipment with the DR® ALLTERRAIN ™ MOWER engine running. Make sure rotating components have completely stopped and the spark plug wire is disconnected BEFORE making any adjustments. 4. Keep the DR® ALL-TERRAIN™ MOWER/ equipment clean. Build-up of debris can lead to malfunction or serious personal injury. 5. Always wear eye protection when cleaning or servicing the equipment. 6. Do not modify or alter this equipment or any of its components or operating functions. 7. Change the oil to an appropriate grade for winter use. Consult your engine manufacturer's owner's manual. Storage Before storing the equipment, certain precautions should be taken to protect it from deterioration: ! WARNING: Always disconnect the spark plug wire before servicing your machine. 1. Clean the equipment thoroughly. 2. Make all the necessary repairs. 3. Replace all Safety Decals that are damaged, lost, or otherwise become illegible. If a part to be replaced has a decal on it, obtain a new safety decal and install it in the same place as on the removed part. 4. Repaint all parts from which paint has worn or peeled. 5. When the DR® SNOW THROWER is dry, lubricate all moving parts. Apply Fluid Film® or comparable lubricant liberally to all surfaces to protect against rust. 6. Store in a dry place. DR® SNOW THROWER Safety, Operation & Maintenance Instructions DECALS Replace Immediately if Damaged (See Parts section for decal location) 657762 660988 660263 660265 657761 DR® SNOW THROWER Safety, Operation & Maintenance Instructions ASSEMBLY & INSTALLATION Step 1: Preparation (Figure 1) After opening the crate and removing all the cardboard, remove the box containing the chute and the instructions (item 2). 1. Remove the two screws (item 4) that retain the housing (item 1) on the pallet (item 3). 2. Verify that you have all components on the following list: If anything is missing, please call one of our Customer Service Representatives TOLL-FREE 1(800)DR-OWNER(376-9637). Crate Qty Item 1 DR® SNOW THROWER assembly 1 Chute assembly 1 Rotation handle 1 Worm shaft 1 Bag Bag 1 Handle support 3 Retaining plates 1 U bolt 1/4" NC x 1 1/8" x 2", PTD 2 Plastic bushings 6 Hex. bolts 1/4" NC x 1/2", PTD 6 Flange nuts 1/4" NC, PTD 1 Flatwasher 41/64" I.D. 1 Hairpin 2mm x 41mm, PTD 1 Cotter pin 1/8" x 1 3/4", PTD 1 Operator's Manual 1 Packing list 1 Spare shear bolt Figure 1 DR® SNOW THROWER Safety, Operation & Maintenance Instructions ASSEMBLY & INSTALLATION Step 2: Chute Installation...