Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. SPEED CON TROL ROD SPEED CONTROL BRACKET RETAINER SPRING SPEED CONTROL LEVER FIG. 2 SPEED CONTROL ROD HANDLE KNOB LOWER HANDLE PLASTIC TIE UPPER HANDLE FIG. 1 INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower. 1. Remove plastic tie securing rod to lower handle. 2. With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring. TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RETAINER SPRING TRACTION DRIVE CON TROL LEVER FIG. 4 TRACTION DRIVE CONTROL ROD VINYL SLEEVE FIG. 3 PLASTIC TIE ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end. 2. Hook end of spring into control arm with loop opening up as shown. (See Fig. 5) 3. With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring. AUGER CONTROL ROD CONTROL ARM VINYL SLEEVE LOOP OPENING UP FIG. 5 INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower. 2. Position chute rotator head over chute bracket. If nec essary, rotate chute assembly to align square and pin on under side of chute rotator head with holes in chute brack et. 3. With chute rotator head and chute bracket aligned, po si tion chute rotator head on pin and threaded stud of mounting bracket. 4. Install 3/8 washer and locknut on threaded stud and tighten securely. CHUTE ROTATOR HEAD 3/8 WASHER 3/8 LOCKNUT THREADED STUD PIN ROTATOR HEAD MOUNT ING BRACKET CHUTE BRACKET FIG. 7 ALIGN BEFORE TIGHTENING LOCKNUT AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RETAINER SPRING FIG. 6 6 ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Eyelet will be loose on shoulder bolt. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown. HOOK BE TWEEN HEX NUTS ON CHUTE ROTATER HEAD SPRING CHUTE DE FLEC TOR 5/16-18 CARRIAGE BOLT 5/16-18 LOCKNUT REMOTE CABLE BRACKET 1/4-20 LOCK NUT CABLE EYELET 1/4-20 SHOULDER BOLT FIG. 8 CHUTE DEFLECTOR CONTROL LEVER FIG. 9 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. 7 OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT. FORWARD REVERSE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. IGNITION KEY. INSERT TO START AND RUN, PULL OUT TO STOP. DISENGAGED ENGAGED SNOW TRACTION DISCHARGE DRIVE CONTROL 8 9 OPERATION Traction drive control lever - used to engage powerpro pelled for ward or reverse motion of snow thrower. Auger control lever - used to engage auger motion (throw snow). Deflector remote control lever - used to change the dis tance the snow is thrown. Discharge chute control lever - used to change the direc tion the snow is thrown. Skid plate - used to adjust height of scraper bar from the ground. Toolbox - used to store spare shear bolts, locknuts and wrench. Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use. Electric start button - used for starting the engine. Recoil (auxiliary) starter handle - used for start ing the en gine. Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine. Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine. MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. TRACTION DRIVE CONTROL LE...
Dieses Handbuch ist für folgende Modelle:Schneefräsen - PP115E27 (2.97 mb)