Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Anschutz Dateigröße: 270.32 kb Dateiname: Unterrichtssprache:

The rifle is now ready for shooting. r et r et Trigger Warning: Your ANSCHUTZ target rifle offers you a versatility of individual adjusting properties. Please make sure that your rifle always is unloaded when carrying out adjustments. 1. Trigger weight Adjust the trigger weight with set screw No. 2: •if you turn it to the right: trigger weight is increased (+) •if you turn it to the left: trigger weight is decreased (-) Trigger weight and first stage weight depend on each other with regard to the mechanic mechanism. If one of them is changed there will always be a corresponding change of the other as well. 2. Sear engagement The sear engagement is the distance between the second stage and the release of the trigger. Important note: To protect your precise trigger and to guarantee perfect operation you should always close the action carefully. If the sear engagement of single stage triggers is too small and the trigger weight is too low or if the first stage of two-stage triggers is too short, the trigger might release inadvertently by a sudden impact or too powerful closing of the action if the gun is loaded and not in the ”safe“ position. Adjustment of the sear engagement for assembled two-stage triggers with set screw No. 1: •if you turn it to the left: sear engagement is shortened •if you turn it to the right: sear engagement is extended Adjustment of an optimum sear engagement: Make sure your rifle is not loaded. Cock your rifle and release the trigger. Check if the trigger releases as desired. The sear engagement is too long: There is a small distance between the second stage and the release of the trigger. •Turn set screw No. 1 counter-clockwise after cocking and releasing (approximately 1/8 turn each). •Repeat this process until you do not feel the second stage anymore. Then turn 1/4 turn back to the right. Thus the optimum sear engagement is adjusted. The sear engagement is too short: There is no second stage. The trigger releases undefined without second stage. •Turn set screw No. 1 clockwise for at least 1/4 turn after cocking. Then release the trigger and check if there is a second stage. If not, repeat this procedure until you feel a second stage. •As soon as you feel a second stage proceed according to the points of the paragraph „The sear engagement is too long“ to obtain an optimum sear engagement. Adjustment of the optimum sear engagement for assembled single stage triggers with set screw No. 1: •Cock the rifle. •Turn set screw No. 1 (first stage) as long to the right until the trigger releases. •Turn set screw No. 1 from this position approx. 1/4 turn to the left. Warning: Single stage triggers are very sensitive and must be operated with special care. The sear engagement of 5/100 mm is obtained after the action is closed. In combination with a minimum trigger weight there might be a malfunction and an increased risk (independent shot release). 3. Malfunctions of the trigger due to wrong adjustment procedure If the trigger is not adjusted correctly malfunctions may occur, tampering with the trigger adjustments will not result in any success. Therefore proceed as follows: After every change the function of the trigger must be checked. When the malfunction is removed check the desired trigger values and adjust them again if necessary. The trigger catches the cocking piston or firing pin, but the trigger does not release: •Make sure that the safety of the trigger is released. The trigger does not catch the cocking piston or firing pin: •The first stage trigger is adjusted too tightly. •Turn set screw No. 1 approx. 1-2 turns to the left. Procede according to par. 2. 4. Maintenance Please see chapter „Cleaning, maintenance, care, oils“. r et r et Adjustment of the trigger blade: After loosening clamping screw No. 3 the trigger blade can be moved in longitudinal direction. Important note: To protect your highly accurate trigger and to maintain perfect functioning always close the bolt carefully. Attention: If you change the trigger remove the bolt from the receiver when fitting the trigger as otherwise the trigger will be damaged. 24 Order No.ModelTwo-stagetriggerSingle-stagetriggerAdjusted toRight handversionLeft handversionFor modelsFor small boremodelsproduction yearsFor small boremodels serial-no. starting from 700.6540 1407-U9 l 150 g l 1407, 1407 Z, 1409, 1411 1413, 1408 EDS 1959 - 1974 700.6541 1408-U1 l 500 g l 700.6542 1408 D-U1 l 500 g l 700.6550 5071/1 l 100 g l 1607, 1613, 1608 EDS 1974-1979 143655 to 182155 700.6560 5071/1 D l 100 g l 700.6570 5075/1 l 550 g l 700.6580 5075/1 D l 550 g l 700.6600 5018 l 100 g l 1807, 1907, 1807 Z, 1907 Z 1907 Silh., 1807 Rep. 1907 Rep., 1907 Rep., 1912 1813, 1913, 1808 EDS 1808 D-RT, 1827, 1827F, 2007 2007/660, 2012, 2013 2013/690, 2013 Benchrest 54.18 MSR, 1808 MSR 2002 Compressed Air, 2020, 2025 starting from 1979 starting from 182156 700.6610 5018 L l 100 g l 700.6620 5018 D l 150 g l 700.6630 5018 L D l 150 g l 700.6640 5020 l 550 g l 700.6650 50...

Herunterladen

Geben Sie zwei Ziffern: