Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Cannon Dateigröße: 179.57 kb Dateiname: Unterrichtssprache:

DO NOT USE ABRASIVES. Aluminium Hotplate side trims, hotplate burner bodies, lid rear trim, rear flue grille. Similar to paint cleaning above. Use a nylon brush to remove any cleaning materials, water or dirt from the hotplate burner bodies. Glass As for enamel cleaning. Polish with a clean dry cloth or kitchen roll. Chromium Plating Oven shelves, grill pan grid, grill pan handle support Wipe with a cloth wrung out in warm soapy water. A fine steel wool soap pad e.g. Brillo, Ajax, or a chrome or stainless steel cleaner may be used. Plastic Grill pan handle, control knobs Wipe with a cloth wrung out in warm soapy water. Stubborn stains can be removed with a cream cleaner. Stainless Steel (Professional) Door trims, control panel, hotplate Wipe with a cloth wrung out in warm soapy water. Polish with a clean dry cloth or kitchen towel. For stubborn stains use a proprietary stainless steel cleaner and follow the instructions on the container. CARE AND CLEANING Take particular care not to damage the inner surface of the door inner glass that is coated with a heat reflective layer. Do not use scouring pads, or abrasive powder, which will scratch the glass. Ensure that the glass panel is not subjected to any sharp mechanical blows. Stubborn stains can be removed by using a fine steel wool soap pad. For slight soiling the inner glass panel may be cleaned, while still warm, without removing it from the door. After cleaning, rinse and dry with a soft cloth. CLEANING THE DOORS SIDE OPENING DOORS Cleaning the door glass is the same as the drop down doors, except take care to support the weight of the inner glass when removing and refitting. DROP DOWN DOORS Remove the door inner glass as follows. 1. Open the door fully and unscrew the two screws securing the glass panel so that the securing brackets can be turned. There is no need to remove the screws completely. 2. Turn the brackets so that the glass can be removed and cleaned at the sink (Fig. 1.) Fig. 1. Glass 3. The inside of the outer door glass can now be cleaned while still fitted to the cooker. NEVER OPERATE THE COOKER WITHOUT THE INNER DOOR GLASS IN POSITION. Refit the door inner glass as follows. 1. NOTE: The inner door glass has a special reflective coating on one side. Replace the door inner glass so that the statement: “IMPORTANT THIS FACE TOWARDS THE OVEN” can be read from the inner side of the door. 2. Turn the two securing brackets back to their original position to retain the glass and tighten the screws. (Fig. 2.) Fig. 2. Glass SOMETHING WRONG WITH YOUR COOKER Before contacting your Service Centre or Installer, check the problem guide below, there may be nothing wrong with your cooker. Burner ports Ignitor Burner ports Ignitor PROBLEM CHECK If all burners fail to ignite: Check that sparks appear at the burners; a clicking Ignition does not work. noise should be heard. If not; Oven burner Check that the electricity supply is turned on. If the electricity supply has failed, the hotplate, grill and top oven burners can be lit by a match. If only one burner fails to ignite: Check that the burner is dry and that spillage of food or cleaning fluid remains are not affecting the ignitor or burner ports. Clean away any debris with a dry nylon brush such as an old toothbrush. If a wire wool pad has been used for cleaning around the burner ensure the ignitor is free from any stray strands. Any water on the burner should be dried with a cloth or kitchen towel. Grill burner Hotplate burner On the hotplate make sure that all the burner parts are correctly seated. Burner ports Ignitor SOMETHING WRONG WITH YOUR COOKER Cannot set an “Auto Cook” programme or cannot get the timer to turn the oven on or off at the required times. Oven lamp does not work PROBLEM Main oven does not work, but the grill, top oven and hotplate burners work. Slight odour or small amount of smoke when grill / oven used first time Oven cooks too fast or too slow Timer Display shows "0:00" with "Auto" Flashing. Read the Timer instructions in this book carefully remembering that the Cook period is the length of time that the timer will switch the oven(s) on as part of an Auto Cooking Programme. The oven lamp is not covered by the guarantee. The part is easily changed (see the section on oven lamp replacement). A new lamp may be obtained from our Spare Parts department, see Key Contacts (back page). CHECK The timer may be set for an Auto Cooking Programme. Check the timer to see if “AUTO” is illuminated. If it is, follow the instructions given in the timer section of this book to cancel the Auto Cooking Programme. This is normal and should cease after a short period. Check that the gas mark and shelf positions are as recommended in the Oven Cooking Charts. However, it may be necessary to increase or decrease the recommended setting slightly to suit your taste. The electricity supply to the cooker may have been been interrupted, but has now come back on again. set the correct time of day by following ...

Herunterladen

Geben Sie zwei Ziffern: