Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Use the menu key to select the desired setting. p* Print Data —► Print Position —| • To return to the previous setting (in step 2), press the esc key. p r i n t D a t a D a t e + C o u n t • Setting the print position 7 Press the menu key until "Print Po sition" is displayed. p r i n t P 0 s i t i 0 n ? < 0 C h a r > 1 0 0 m m 18 Display Panel Instructions 2 Use the ▼ key or the ▲ key to select the desired print position. • The printout, by the display shown above, will print starting 12.4 mm (approx. 1/2 in.) from the top of the paper, but this position can also be changed by the print position setting. Top of the paper 12.4 mm [Approx .1 Li/2 in J Top of the printout that is set newly. For the setting shown on the right, the " B" position will become the beginning of the printout. 10 mm [Approx. 1 JL13/32 in.J, 00 P r i n t P o s i t i 0 n ? < 1 c h a r > 1 2 4 m m 3 Press the enter key. • To return to the previous LCD setting (in step 1), press the esc key. P r i n t p 0 s i t i 0 n < 1 c h a r > 1 2 4 m m ■Clearing the warnings You can clear the following warnings on the display. Clean Roller : The alarm tells you it is time to check the roller. If it is near 100%, clean the roller. See "Cleaning the Unit" on page 32. Replace Roller : The alarm tells you the roller needs to be changed. If it is near 100%, replace the paper feed roller module and retard roller module. See "Replacing the Roller Modules" on page 37. Replace F-Lamp: The alarm tells you the front side scanning lamp needs to be changed. If it is near 100%, ask your dealer to replace the front side lamp module. Replace B-Lamp: The alarm tells you the back side scanning lamp needs to be changed. If it is near 100%, ask your dealer to replace the back side lamp module. • To clear the clean roller 7 Press the menu key until "Clear Warning" is displayed. C I e a r W a r n i n 9 2 Press the enter key. C I e a n R 0 I I e r 2 0 % C I e a r = E N T E R 19 Display Panel Instructions Press the enter key. • To return to the previous setting (in step 2), press the esc key. The LCD will return to the display shown in step 1. • After entering the warning display mode, pressing the menu key will change the display as follows. Use the menu key to select the desired setting. Clean Roller — Replace Roller —i i— Replace F-Lamp *-' ^ Replace B-Lamp- c I e a n R 0 I I e r 0 % C I e a r = E N T E R • To clear other warnings 7 Press the menu key until the desired warning is displayed. Warning display for replacing the roller R e P I c e R 0 I I e r 2 0 % C I e a r — E N T E R Warning display for replacing the front side lamp module R e P I c e F - L a m P 2 0 % C I e a r = E N T E R Warning display for replacing the back side lamp module R e P I c e B - L a m P 2 0 % C I e a r = E N T E R 2 Press the enter key. • To return to the previous setting (in step 1), press the esc key. The LCD will return to the "Clear Warning" display. Warning display for replacing the roller R e P I c e R 0 I I e r 0 % C I e a r — E N T E R Warning display for replacing the front side lamp module R e P I c e F - L a m P 0 % C I e a r = E N T E R Warning display for replacing the back side lamp module R e P I c e B - L a m P 0 % C I e a r = E N T E R 20 Display Panel Instructions ■Setting other parameters The following parameters can be set. Language: Sets the display language (English, Japanese). Buzzer : Sets whether a bell rings or not If set to "ON", the following will occur. When pressing a button, one short beep will be heard. When there is an error, 4 short beeps will be heard. When scanning is completed correctly, one long beep will be heard. Date : Sets the current date. Time : Sets the current time. Version : Displays the unit version. • Setting the language ^ Press the menu key until "Set J Other Param." is displayed. s e t 0 t h e r P a r a m ^ Press the enter key. L a n 9 u a 9 e E n 9 1 i s h X -r Zl * 3Use the ▼ key or the ▲ key to select "English" or "Japanese". L a n 9 u a 9 e ? J a P a n e s e _ * > =1 * 4 Press the enter key. • To return to the previous setting (in step 2), press the esc key. After entering the other parameter setting mode, pressing the menu key will change the display as follows. Use the menu key to select the desired setting. I—► Language -* Buzzer -* Date —i '- Version «—Time *-* L a n 9 u a 9 e J a P a n e s e _ * > Zl ♦ Display Panel Instructions • Setting the buzzer 7 Press the menu key until "Buzzer" is displayed. B u z z e r 0 N 2 Use the ▼ key or the ▲ key to select "ON" or "OFF". B u z z e r ? 0 F F 3 Pres...