Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
• Do not use thinner, benzine, or cleaners containing abrasives or surfactants, for cleaning the outside of scanner. • Plug the power cord into an outlet from which you can easily unplug it. Operating Manual Before You Start Before You Start It is unlawful to make duplication of certain documents. Duplicating certain documents may be illegal in your country/area. Penalties of fines and/or imprisonment may be imposed on those found guilty. The following are examples of items that may be illegal to duplicate in your country/area. • Currency • Bank notes and checks • Bank and government bonds, and securities • Passports, licenses, official or private documents, identification cards, and the like • Copyright materials, or trademarks without the consent of the owner • Postage stamps, and other negotiable instruments This list is not inclusive, and no liability is assumed for either its completeness or accuracy. In case of doubt, contact your legal counsel. Notice Install your machine near a supervised area to prevent illegal duplication from being made. Security Notice The management of documents and scanned data is the responsibility of the user. In particular, pay attention to the following points. • Make sure you have the same number of pages for important documents both before and after scanning, and take care not to leave any pages in the scanner. • Periodically back up important data. • When having your computer or hard disk serviced, or when disposing of your computer or hard disk, completely erase any stored image data. Caution Labels HOT SURFACEDO NOT TOUCH. The glass in the scanning area becomes very hot. Exercise care not to touch heated areas, or you may get burned. CAUTION Operating Manual Main Unit Front 1 2 m l j 9 3 k 4 6 7 5 8 Document guides Door open button ADF door Exit tray Exit extension tray Exit stopper Scanning lamps Start / Stop button • If you set [Wait Key] for "Manual Feed Mode"*1 in your application software, pushing this key starts scanning. • During scanning, pushing this key stops scanning. Security slot (for security cable) LED (Red) Shows the scanner’s status. For details, see "About LED" (page 13). LED (Green) Shows the scanner’s status. For details, see "About LED" (page 13). Feed tray Feed extension tray *1 For details on "Manual Feed Mode", refer to the RTIV Reference Manual or PIE Reference Manual. Operating Manual 11 L o c a t i o n o f C o n t r o l s Location of Controls Location of Controls Location of Controls r 6547123 Mixed batch card guide Power connector Power switch AC adaptor Power cord Plugs may vary in shape depending on country/area. USB cable USB connector Operating Manual Operation Operation r 1. Press the power switch (A) of the scanner to ON. 1 • The LED (Green) will blink for about 30 seconds, and then it will become steady. About LED The status of the scanner can be established by the condition of the two LED indicators shown in the table below: ReadyErrorStart / StopAB A LED (Green) ON ON Blink (Fast) Blink (Slow) Blink (Slow) OFF B LED (Red) OFF Blink (Slow) OFF OFF Blink (Slow) ON Status Ready Caution Warming up*1 Sleep Caution / Sleep Error *1 It will take about 30 seconds to initialize the scanner under the following conditions: – Just after turning the power on – After about 2 hours on sleep mode – Over about 5 seconds with the ADF door open Operating Manual Operation Operation The scanner application can be configured to start automatically when pressing the Start / Stop button, and/ or placing documents on the feed tray. To accomplish this, follow the steps below. Setting the event 1. Click [Start], and then click [Control Panel]. • In Windows 2000, click [Start], and then click [Setting] - [Control Panel]. 2. Select your scanner in the [Scanners and Cameras], and then display the scanner property dialog box by right clicking on the scanner icon. • In Windows Vista and Windows 2000, select your scanner in the [Scanners and Cameras Properties], and then display the scanner property dialog box by clicking [Properties] button. 3. Click the "Events" tab. 4. Select an event in the "Scanner events" list. The selected event activates a scanner application. • The following events can be selected. "Feeder Loaded" An event occurs when placing documents on the feed tray. "Start Button"*1 An event occurs when pressing the Start / Stop button of the scanner. *1 If the scanner goes into sleep mode, you must press the Start / Stop button twice. Operating Manual Operation 5. Select the check box of the desired scanner applications corresponding to the selected event in the "Send to this application" list. • To disable the automatic activation of the scanner applications, set the "Disable device events" check box to on. 6. Click [OK]. Note • When multiple applications are selected in the "Send to this application" list, the "Choose Application" dialog box will display, prompting you to select an application in the "Registered Applications" list. After an applica...