BROAw Nulbne* SPECIFICATION SHEET MODELS 331H & 332H EXTERIOR BLOWERS Use this high-powered ventilator to quietly and efficiently exhaust airborne contaminants from cooking and living space. FEATURES: • Brushed aluminum construction • Built-in flashing plate for roof or wall mount • Built-in backdraft damper and birdscreen • Easily removable cover provides quick access to blower for cleaning and servicing • For 10" round duct • Thermally protected, permanently lubricated motor • Spee

Set the air compressor to 30 - 100 working PSI. Do NOT exceed 110 PSI. 3. Squeeze Air Blow Gun trigger to begin the flow of air. 4. Release Air Blow Gun trigger to stop the flow of air. 5. When finished, turn off the air compressor and then disconnect Air Blow Gun from the air source hose 6. Only use clean and dry compressed air. Never use oxygen, carbon dioxide, combustible gases or any other bottled gas as a power source. 92363 951 59 For technical questions and replacement parts, pleas

Set the air compressor to 30 - 100 working PSI. Do NOT exceed 110 PSI. 3. Squeeze Air Blow Gun trigger to begin the flow of air. 4. Release Air Blow Gun trigger to stop the flow of air. 5. When finished, turn off the air compressor and then disconnect Air Blow Gun from the air source hose 6. Only use clean and dry compressed air. Never use oxygen, carbon dioxide, combustible gases or any other bottled gas as a power source. 92363 951 59 For technical questions and replacement parts, pleas

(2,743 mm) WIDTH 100 in. (2,540 mm) WEIGHT 1,605 lbs. (729 kg) BLOWER Blowing height* Over 100 ft. (Over 30 m) Blower housing 60 in. dia. (1,524 mm) Paddles (adjustable) 8 Paddle tip speed 8,460 ft./min. (2,579 m/min.) Drive Direct PTO HOPPER Diameter Auger-12 in. (305 mm) Length Auger-50 in. (1,270 mm) Width 37 in. (940 mm) Height from ground Adjustable-201/2 in. (520 mm) to 27/s in. (699 mm) Feeder type Auger DRIVELINE PROTECTION Shearbolt PTO 540 rpm TIRES 4.80-8 “C” load

Where these components are not protected by ductwork, cabinets or covers, appropriate guards should be employed to restrict exposure to rotating parts. Access doors should not be opened with the fan operating to avoid foreign objects being drawn into the system. On initial start-up a careful inspection should be carried out to ensure no foreign material is present which could become airborne in the system. Read installation and operation instructions carefully before attempting to install, oper

Remove any excess lubrication. 3. Clean the blower wheel periodically. Material build up on the blades can cause wheel imbalance which may result in wheel or motor bearing failure. Parts List 1 Cabinet 2 Side Access Panel 3 Motor 4 Wheel 5 Inlet Venturi Warranty Delhi Industries Inc. Air Moving Products are guaranteed for a period of one year against manufacturing defects in material and workmanship when operating under normal conditions. Liability is limited to the replacement of defe

Complete electrical connections as indicated. Warning: A ground wire must be connected from the motor housing to a suitable electrical ground. Motor Wiring Diagram DSQ-D-10, 12 & 13 MOTOR WIRING - SINGLE SPEED '■VHITE t L HE 1 SLACK gREEN _|||. GROUND TO 1 JUNCTiOH BOX DSQ-D-15 MOTOR WIRING - TWO SPEED VHJLÛW . LOW. OP i" lime : GRDUNDTO JUHCTIOH BOX Speed Control Wiring Diagram For DSQ-D10, 12 & 13 Single Speed Motors Only a swrcn K TPiAC AC LINE CONNECTIION DIAGRAM