Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
D Store in a dry area out of reach of children. SPECIAL NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An antivibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. SPECIAL NOTICE: For users on U.S. Forest Land and in some states, including California (Public Resources Codes 4442 and 4443), Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington: Certain internal combustion engines operated on forest, brush, and/or grass covered land in the above areas are required to be equipped with a spark arresting screen, maintained in effective working order, or the engine must be constructed, equipped, and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these requirements is a violation of the law. This unit is not factory equipped with a spark arresting screen; however, a spark arresting screen is available as an optional part. If a spark arresting screen is required in your area, contact your authorized service dealer for the correct kit. The spark arresting screen, blower tubes, and nozzles must be assembled to unit to be in full compliance with regulations. --4 - - ASSEMBLYASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or accessing movable parts. WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit. D A standard screwdriver is required for assembly. BLOWER TUBE ASSEMBLY 1. Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place. NOTE: Knob must be loose enough to allow blower tube to be inserted in blower outlet. Loosenknobbyturningcounterclockwise. BlowerTubeBlowerOutletRibGroove2.Securethetubebyturningtheknobclockwise. 3. To remove the tube, turn the knob counterclockwise to loosen the tube; remove the tube. VACUUM BAG ASSEMBLY 1. Open the zipper on the vacuum bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. SmallOpeningZipperOpeningElbowTubeRib NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom. 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Remove blower tube from engine. --5 - -- Groove Rib 5. Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove. 6. Turn knob clockwise to secure elbow tube. VACUUM TUBE ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. 1. Align the lower vacuum tube as shown. Push lower vacuum tube into upper vacuum tube. LowerVacuumTubeUpperVacuumTube 2.Insertthetipofascrewdriverintothelatchareaofthevacuuminlet. LatchAreaBlowerOutletVacuumInletCoverLatchArea 3. Gently tilt the handle of the screwdriver toward the back of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. 4. Hold the vacuum inlet cover open until upper vacuum tube is installed. VacuumInlet Retaining Post Vacuum Inlet Cover 5. Place the hooks of the upper vacuum tube on the retaining posts of the unit. 6. Pivot the tube until it is secured to the blower unit by the vacuum inlet latch. RetainingPostHookInletCoverLatchPIVOT HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area of the vacuum inlet. 2. Gently tilt handle of screwdriver toward the back of the unit to release the latch while pulling up on the upper vacuum tube with your other hand. LatchArea 3. Remove the vacuum bag. 4. Close the vacuum inlet cover and make sure it is latched closed. 5. Reinstall the blower tube (see BLOWER TUBE ASSEMBLY). SHOULDER STRAP ADJUSTMENT 1. Hold the unit as shown with the muffler side facing away from your body and clothes. 2. Pass the shoulder strap over your he...