Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Disconnect spark plug wire and keep wire away from plug to prevent accidental starting. Also keep throttle control lever in the stop position. If the power vacuum should become blocked with debris at any point, shut engine off and wait until the impeller comes to a complete stop before attempting to remove the obstruction. Disconnect spark plug wire to prevent accidental starting. 10. Check all bolts for tightness at frequent periods. 11. Never store this power vacuum with fuel in the tank. Allow engine to cool before storing in any enclosure. 12. Keep bag and equipment free of debris when not in use. 13. Never operate this power vacuum unless air duct and vacuum bag are "properly affixed in their place. Large zippered end of bag must be closed when operating to prevent objects from being blown out. 14. Never empty vacuum bag when engine is running. 15. Never change inlet nozzle or auxiliary hose attachment when engine is running. 16. The manufacturer recommends that the operator wear safety glasses or some other suitable eye protection when operating this machine. 17. Check the vacuum bag frequently for wear and replace when necessary. 18. Never operate as a leaf blower unless impeller guard and guard assembly are properly affixed in their place. 19. Exercise caution whenever operating as a leaf blower. Do Not allow discharge to be pointed in the direction of persons. 20. No one should operate this unit while intoxicated or while taking medication that impairs the senses reactions. H FIGURE 2 ASSEMBLY INSTRUCTIONS CONTENTS OF HARDWARE PACK (See Figure 1.) A (1) Clutch Grip Assembly B (1) Hair Pin Cotter C (1) Clevis Pin D (1) Extension Spring E (1) Lock Nut 1/4-20 Thread F (3) Hand Knobs G (3) Belleville Washers H (1) Heavy Flat Washer I (4) Hex Bolts 1 /4-20 x 1.75" Long J (4) Hex Lock Nuts 1/4-20 Thread K (2) Stud Pins L (2) Push-on Speed Nuts M (1) Hex Jam Nut 1/4-20 Thread (Not Shown) LOOSE PARTS IN CARTON (See Figure 2.) N ( 1) Nozzle 0 ( 1) Upper Handle P ( 1) Air Duct Assembly Q ( 1) Clutch Rod R ( 1) Directional Discharge Assembly S ( 1) Impeller Guard T ( 1) Bag NOZZLE (N) FIGURE 3 1. Place nozzle (N) in position on front of housing so that it rests in flanges. Secure with one hanc knob (F) and bellevilie washer (G). See figure 3. 4 2. Place the upper handle (0) in position over lower handle. Fasten with four hex bolts (1) and lock nuts (J) provided. See figure 4. Two 7/16" wreriches are required. :IGURE 4 3. Place the stud pins (K) in holes in upper handle (head of pins go to the inside of handle). Secure pins with push-on speed nuts (L) by holding speed nut with box wrench and tapping pin with hammer. See figure 5. :IGURE 5 HAND KNOB (F) :IGURE 6 4. Place air duct assembly (P) over opening on top of housing. Secure with two hand knobs (F) and belleville washers (G). See figure 6. 5 STUP PIN ON HANDLE 5. Assemble the bag by slipping the top straps on bag (T) over upper handle. Hook two small straps over stud pins on handle. Slip elastic opening of bag over air duct assembly. See figure 7. BAG (Ti NOTE Be certain elastic on bag is placed over the flanges on air duct assembly. FIGURE 7 Assemble the clutch grip (A) to the left hand side of upper handle. Secure in place with clevis pin (C) and hair pin cotter (B). See figure 8. Head of clevis pin should be to the outside of handle. FIGURE 8 7. Slide the extension spring (D) onto clutch rod (Q) as shown in figure 9. Thread lock nut (E) onto clutch rod approximately 2 1/2 inches. ROD (Q) FIGURE 9 6 CLUTCH BRACKET ASSEMBLY FIGURE 10 HAND KNOB 8. Hook top (hooked end) of clutch rod into clutch grip. Hook spring into clutch bracket assembly. See figure 10. Spring should not have any slack. Adjust nut so that when the clutch grip is all the way up, there is no slack in the spring. 9. Thread hex jam nut (M) onto clutch rod and lock against the lock nut. Ac WARNING \ Engine must be stopped (off) and spark plug wire disconnected. ASSEMBLY INSTRUCTIONS To Convert from a Vacuum to a Leaf Blower. 1. Remove the bag. 2. Remove the air duct assembly by removing two hand knobs and belleville washers. 3. Remove the nozzle by removing one hand knob and belleville washer. 4. Remove the hand knob and belleville washer holding the housing to engine brace. See figure 11. FIGURE 11 FIGURE 12 5. Lift up and out on the housing and rotate it 105° clockwise. Chute opening should be to the right hand side when viewed from the front of unit. See figure 12. 6. Place the impeller guard (S) into flanges on front of housing. Line up hole in screen with hole on housing. Secure with one hand knob, belleville washer and heavy flat washer (H). See figure 12. 7 HAND KNOB DIRECTIONAL DISCHARGE ASSEMBLY (R) 7. Place the directional discharge assembly (R) over chute opening. Secure with two hand knobs and belleville washers. See figure 13. A FIGURE 13 CAUTION REVOLVING BLADES-KEEP HANDS AWAY FROM ALL ...