Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
TUBE RELEASE BUTTON The TUBE RELEASE BUqq-ONsecures the blower tube or elbow tube to the blower unit during operation. Also, pressing the tube release button allows removal of the blower tube or elbow tube. z_ 4rLWARNING: You MUST make sure the tubes are secure before using the unit. _WARNING: Do not use the unit without the tubes or collection bag properly attached to avoid flying debris and/ or impeller contact which can cause se rious injury. Always wear eye protection to prevent rocks or debris from being blown or ricocheting into the eyes and face which can result in blindness or se rious injury. STOPPING YOUR UNIT Slide the ON/OFF switch to the OFF position. STARTING YOUR UNIT Your unit has two run positions, LOW and HIGH. Slide the switch to one of these positions to turn on the unit. OPERATING POSITION Eye Protection Eye Protection Blower Vacuum USING YOUR UNIT AS A BLOWER WARNING: Inspect the area before using the unit. Remove all debris and hard objects such as rocks, glass, wire, etc., that can ricochet, be thrown, or otherwise cause injury or damage during operation. Use your unit as a blower for: • Sweeping debris or grass clippings from driveways, sidewalks, patios, etc. • Blowing grass clippings, straw, or leaves into piles, or removing debris from corners, around joints, or between bricks. CUSTOMER RESPONSIBILITIES peller. To avoid the possibility of electrical shock, do not attempt to vacuum water or other liquids. Use your unit as a vacuum to pick up dry material such as leaves, grass, small twigs, and bits of paper. • For best results during vacuum use, operate your unit at high speed. • Move slowly back and forth over the material as you vacuum. Avoid forcing the unit into a pile of debris as this can clog the unit. • Keep the vacuum tube about an inch above the ground for best results. _WARNING: If the unit becomes clogged, stop the unit and unplug the extension cord. Wait until the impeller has completely stopped turning, then remove the vacuum tubes. Carefully reach into the vacuum opening and clear out the clogged debris. Direct air flow by directing the blower tube down or to one side. Always work away from solid objects such as walks, large stones, vehicles, and fences. Clean corners by starting in corners and moving outward. This will help prevent an accumulation of debris which could fly into your face. Be careful when working near plants. The force of the air could damage tender plants. USING YOUR UNIT _'WARNING: Do stones, gravel, metal, etc., to avoid severe AS A VACUUM not vacuum broken glass, damage to the im '_ WARNING: Disconnect power source before performing maintenance. CARE & MAINTENANCE TASK WHEN TO PERFORM Check for loose fasteners and parts Before each use Check for damaged or worn parts Before each use Inspect and clean unit and labels After each use Remove and empty collection bag After each use Clean collection bag Yearly 9 RECOMMENDATIONS GENERAL AFTEREACH USE Thewarrantynot onthisunitdoescover itemsthathavesubjected beentooper atorabuseToreceive ornegligence.full valuefromtheoperator thewarranty, mustmaintainasinstructed unitinthis manual.adjustments Variouswillneed tobemadeperiodically toproperly maintainunit. your BEFOREEACHUSE CHECKLOOSE FOR FASTENERS ANDPARTS • InletCover • Blower Tube • Vacuum Tubes • Collection Bag CHECKFORDAMAGED OR WORN PARTS ContactyourSearsCenter Servicefor replacementorworn ofdamaged parts. • ON/OFF-Ensurefunc- Switchswitch tionsproperlytheswitch bymovingto theOFFposition.sure Makemotor stops;restartandcontinue. thenmotor • InletCoveruse -Discontinueofunitif inletcovertolatchorifit failsproperly isdamagedway. inany HOW TO REMOVE AN OBJECT FROM THE AIR INTAKE ,_WARNING: Stop tile unit and disconnect from the power source before opening the inlet cover. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. 1. While holding the inlet cover open, remove the vacuum tubes. The inlet cover must be held open through all remaining steps. 2. Carefully reach into the vacuum opening and clear out the air intake area. Clear all debris from impeller= INSPECT AND CLEAN UNIT & LABELS Stop unit and unplug extension cord. • After each use, inspect complete unit for loose or damaged parts. Clean the unit using a damp cloth. • Wipe off unit with a clean dry cloth. CLEAN COLLECTION BAG IMPORTANT: THE COLLECTION BAG MUST BE PROPERLY EMPTIED. • You must properly empty and maintain the collection bag to avoid deterioration and obstruction of air flow. • Remove the collection bag from the unit and empty after each use. Do not store bag without emptying the bag of all contents (grass, leaves, etc.). • Wash the bag once a year. Remove the bag from the blower and turn the bag inside out. Wash the bag with a water hose. Allow the bag to hang and dry completely before you reuse the bag. 3. Inspect the impeller for cracks. If cracked or damaged, do not use the unit. Have parts replaced by your Sears S...