Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
To install the vacuum tubes: • Secure the upper and lower vacuum tubes together by aligning the raised locking tabs with the raised slots. • Tap tube assembly on ground until the screw holes in lower tube are in the raised slot of the upper tube. Secure with supplied screws. • Depress door tab using a flathead screwdriver and open vacuum inlet door. • Align screw mounts on vacuum opening with screws on vacuum tube assembly. • Turning clockwise, tighten screws on upper vacuum tube to secure to blower housing. To remove the vacuum tubes: • Loosen screws of the upper vacuum tube by turning counterclockwise. • Remove the vacuum tube assembly from the blower housing. • Close the vacuum inlet cover door securely. 7 - English OPERATION WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing protection. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries. APPLICATIONS You may use this product for the purposes listed below: • Clearing leaves and other debris from your lawn • Keeping decks and driveways free from leaves and other forms of debris • Vacuuming leaves from your lawn MIXING THE FUEL This product is powered by a 2-cycle engine and requires premixing gasoline and 2-cycle oil. The mixture should be at a 50:1 ratio. NOTE: We recommend you use ONLY Ryobi (exact mix) your product. To mix the fuel: • Use a clean container that is approved for use with gasoline. • Mix the 2-cycle engine oil with unleaded gasoline in the container, according to the instructions on the oil package. This engine is certified to operate on unleaded gasoline intended for automotive use with an octane rating of 87 [(R + M) / 2] or higher. Do not use automotive oil or 2-cycle outboard oil. NOTE: Most fuel mixture will stay fresh up to 30 days. DO NOT mix quantities larger than usable in a 30 day period. 2-CYCLE FUEL / OIL MIX (50:1) GASOLINE OIL 1 gallon (US) 2.6 oz. 1 liter 20 cc (20 ml) FILLING THE TANK • Clean the surface around the fuel cap to prevent contamination. • Loosen the fuel cap slowly by turning counterclockwise. • Pour the fuel mixture carefully into the tank. • Clean and inspect the fuel cap gasket before replacing the fuel cap. • Replace the fuel cap and tighten it by turning it clockwise. • Wipe spilled fuel from the product. • Move at least 30 ft. away from refueling area before starting the product. NOTE: It is normal for smoke to be emitted from a new engine during first use. WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks. Failure to safely handle fuel could result in serious personal injury. OXYGENATED FUELS DO NOT USE E85 FUEL. IT WILL VOID YOUR WARRANTY. NOTE: Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated previously are not covered under warranty. Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) or 15% ethanol by volume (commonly referred to as E15) are acceptable. Do not use E85 fuel. STARTING AND STOPPING See Figure 8. Blower should be on a flat, bare surface for starting. • Slowly press the primer bulb 10 times. NOTE: After the 10th press, fuel should be visible in the primer bulb. If it is not, continue to press the primer until you see fuel in the bulb. • Set the choke lever to the FULL CHOKE position. • Lock throttle/cruise control lever. • Pull starter grip and rope sharply until engine attempts to run. Do not pull the starter grip more than four (4) times. • Set the choke lever to the HALF CHOKE position. • Pull the starter grip and rope until the engine runs. NOTE: If the engine does not start, return to the FULL CHOKE position and repeat the steps that follow. • Allow the engine to run for 15 seconds, then set the choke lever to the RUN position. TO STOP THE ENGINE: • To stop the engine, depress and hold the STOP switch to the stop position “ ”. 8 - English OPERATION OPERATION HOT RESTART OF THE ENGINE: • Set the choke lever to the RUN position. • Lock throttle/cruise control lever. • Pull the starter grip and rope until the engine runs. IF ASSISTANCE IS REQUIRED STARTING THIS PRODUCT: Do not return this product to the retail store where it was purchased. Please call our Customer Service Department for any issues you may have. For Help Call: 1-800-860-4050 OPERATING THE BLOWER See Figures 9 - 10. WARNING: Never run the unit without the blower tubes installed or the vacuum door securely closed. Use of an improperly assembled unit could result in serious personal injury. • Start the blower. Refer to Starting and Stopping earlier in thi...