Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Husqvarna Dateigröße: 5.2 mb Dateiname: Unterrichtssprache:

oz/h) 0.58 (19.6) 1.04 (35.2) 1.6 (54.1) 1.85 (62.6) Air Volume (w/std Pipe) cu. m/ min (cf/m) 10.2 (360) 14 (494) 16 (565) 19.4 (685) Air Volume (@ housing) cu. m/ min (cf/m) 12.2 (431) 19.6 (692) 21.0 (742) 25.9 (915) Air velocity m/sec (mph) (Maximum) 65 (145) 80 (180) 88 (198) 90 (201) Noise Level (50 Feet ANSI B175.2-2000) dB(A) 69 71 76 77 Noise emission (see note 1) Sound power level , measured dB (A) 102 104 110 109 Sound power level , guaranteed LWA dB (A) 102 104 110 Sound levels (see note 2) Equivalent sound pressure level at the operator’s ear, measured according to EN15503 dB(A) 91 95 96 (ISO7917) 97 Vibration levels (see note 3) Equivalent vibration levels (a hveq) at handle, measured according to EN15503 m/s2 2.5 2.1 2.3 4.0 4.3 2.1 2.9 • The data shown above are those in the case of one straight pipe. • Specifications are subject to change without notice. • This spark ignition system complies with the Canadian standard ICES-002. Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC. Reported sound power level for the machine has been measured with the original attachment that gives the highest level. The difference between guaranteed and measured sound power is that the guaranteed sound power also includes dispersion in the measurement result and the variations between different machines of the same model according to Directive 2000/14/EC. Note 2: The equivalent sound pressure level value is calculated with a work cycle of a duration of 1/7 for idling and 6/7 for racing. Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation) of 1 dB(A). Note 3: The equivalent Vibration total value is calculated with a work cycle of a duration of 1/7 for idling and 6/7 for racing. Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s2. English 14 ¦ FLEXIBLE HOSE AND SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. (1) Flexible hose (2) Swivel joint (3) Clamp (large) (4) Clamp (small) NOTE A light lubricant may be used to ease assembly of flexible hose to blower elbow. ¦ CONTROL HANDLE [130BT/350BT/370BTS/380BTS] 1. Set up the handle holder to the swivel joint and tighten the knob on the holder. When setting up the handle holder, please make sure to match the handle holder to the convex on the swivel joint as shown in F2. 2. Adjust the position and angle to achieve a comfortable working position, and tighten the control handle. (1) Cabling (2) Flexible hose ¦ CABLING [130BT/350BT/370BTS/380BTS] [130BT] - Fasten the cabling at central position of the hose by the band attached to the cabling. First, wrap the flexible hose with the band fixed to the cabling from the lower side. Then, pass the band through a hole of the band as shown in figure. Please note that there is a possibility of damaging the hose if the band is fastened too tightly. [350BT] [370BTS] [380BTS] - Use the clamp to fasten the cabling to the flexible hose. (1) Clamp ¦ RIGHT HANDLE [350BF/370BFS/380BFS] - Insert the handle holder to the swivel and tighten the knob on the holder. When setting up the holder, please make sure to match the holder to the convex on the swivel joint as shown in F5. ¦ HANDLEBAR [OPTION] [130BT/350BT/370BTS/ 380BTS] 1. Insert the holder, then assemble the handlebar (OPTION) and tighten it securely. (2) (1) (4) (3) F1 (1) (2) F2 F3 [130BT] (1) F4 [350BT] [370BTS] [380BTS] F5 F6 Assembly English 15 ¦ BLOW PIPES Conect the swivel joint, straight pipe and pipe end. Push the pipes together and turn them so they lock in relation to one another until the connection is locked. NOTE A light lubricant may be used to ease assembly of blower tube. NOTE If longer tube is required, the second straight pipe can be connected with the first one. If higher air speed is required, the round blow pipe can be replaced by the flat nozzle with the second straight pipe. (1) Flat nozzle (option) ¦ HARNESS NOTE The harness must always be worn when working with the machine. Failure to do so means you will be unable to maneuver safely and this can result in injury to yourself or others. A correctly adjusted harness and machine significantly facilitates the work. Adjust the harness to give the best working position. Tighten the side straps so that the pressure is evenly distributed across the shoulders. ¦ WAIST BELT [350BT/BF] [370BTS/BFS] [380BTS/BFS] - The waist belt is attached to the rings on the left and right sides of the frame. NOTE 130BT has no waist belt. Place the waist belt around your waist and not too far down on the stomach. Tighten the waist belt strap so that you feel the weight of the blower resting on your hip. - Be sure to always tighten the buckle in front of your body. WARNING - If you are not using a waist belt, be sure to remove it fr...

Herunterladen

Geben Sie zwei Ziffern: